User manual ZANUSSI ER6336U

[. . . ] I N F O INSTRUCTION BOOKLET REFRIGERATOR ER 6336 U 2222682-61 CONTENTS Instructions for the user Important Safety Instructions Description of the Appliance Operation Before use Setting the temperature Fresh food refrigeration The door shelves The -star compartment Freezing fresh food Frozen food storage Thawing Making ice cubes Normal Operating Sounds Instructions for the installer 3 4 4 4 4 4 5 6 6 6 6 6 6 Technical specifications Installation Positioning 15 15 15 Electrical Connection Building-in Instructions Inner door reversal Door Reversal Building the appliance in under a worktop Fitting the plinth 16 17 17 17 19 22 Health and safety guidelines Defrosting Maintenance and Cleaning Internal cleaning External cleaning Periodic cleaning Changing the light bulb When the appliance is not use 7 8 9 9 9 9 9 9 Something not Working?Service and Spare Parts Customer Care Department Guarantee conditions Electrolux Service Force 10 11 11 12 13 2 IMPORTANT SAFETY INSTRUCTIONS These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings or these warnings contact the Customer Care Departement. Prior to Installation s During Use s Check the appliance for transport damage. [. . . ] Take care not to let the meat juices drip onto other food. If the meat does drip, remove everything and clean thoroughly. The best way to defrost food is to put it in the refrigerator to thaw slowly. Ensure that food placed in the freezer compartment is dated and labelled and used in date order to ensure that food is consumed at its best. It is important that food is used before its "best before" date. The foods to be frozen must be fresh and of the best quality. The size of each pack should be small enough to ensure that it is used in one go. Small packs freeze more quickly and uniformly and give better results. Frozen food, once thawed, must not be refrozen. This should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows: 1. pull out the plug from the wall socket or turn the thermostat knob to the «O» setting; 2. remove any stored food, wrap it in several layers of newspaper and put it in a cool place; 3. leave the door open, place a basin on the top shelf of the refrigerator compartment, under the drain hole, remove the plug as shown in the figure; 4. when defrosting is completed, dry the interior thoroughly and refit the plug. Keep the scraper for future use; turn the thermostat knob back to the required setting or replace the plug in the power socket. After two or three hours, reload the previously removed food into the compartment. Important A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. P F S. I. 011 PR151 8 MAINTENANCE AND CLEANING Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. [. . . ] - 89/336 EEC of 3. 5. 89 (Electromagnetic - Compatibility Directive) and subsequent amendments. Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of breakdown. Important The wires in the mains lead are coloured in accordance with the following code: Green and Yellow Blue Brown - Earth - Neutral - Live If you fit your own plug, the colours of the wires in the mains lead of your appliance, may not correspond with the markings identifying the terminals in your plug, proceed as follows: Connect the Green and the Yellow (earth) wire to the terminal in the plug which is marked with the letter «E» or the earth symbol , or coloured green and yellow. Connect the blue (neutral) wire to the terminal in the plug which is marked with the letter «N» or coloured black. Connect the brown (live) wire to the terminal in the plug which is marked with the letter «L» or colured red. [. . . ]