User manual ZANUSSI FLS1222

[. . . ] Hydraulic connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Levelling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Descriptions of the controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] s All packing and transit bolts must be removed before use. s Serious damage can occur to the product and to property if this has not been adhered to. See relevant section (unpacking) in the instruction booklet. s The washing machine must be unplugged when removing the interior transit bolts. Do not plug the appliance before finishing the removal of the transit bolts and the fixing of the caps in the holes where the security bolts were. s If the appliance is to stand on a carpeted floor make sure that there is space between the carpet and the supporting feet of the appliance for the air to circulate freely around . s Care must be taken to ensure that the appliance does not stand on the electrical supply cable. 3 ENGLISH UNPACKING AND INSTALLATION TRANSIT SECURITY BARS Before starting the machine up, the transport security bars must be removed as follows: You are advised to keep all the transport security bars in case the appliance has to be transported again. Unscrew and remove the three rear screws by means of a key. HYDRAULIC CONNECTION There should be a COLD WATER tap near the washing machine with a screwing on connection pipe of 3/4 gas for the water supply, a sink, a wash basin or a drainage system in the wall. Previously check if: -- -- it is not a hot water tap. If not, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. Have the permanent drainage system in the wall checked by a plumber. Place the enclosed rubber joint, delivered in a plastic bag together with the appliance (A), at the very end of the inlet hose and carefully screw the pipe to the tap taking care not to damage the screwdrive and fix the nut well on to the end in order to avoid leaking. Once in the right position fix the feet by pushing the nuts against the base of the case. Accurate levelling will prevent vibration, noise and displacement of the appliance during operation. Some vibration is inevitable, especially if placed on a wooden floor. Wooden floors are particularly susceptible to vibrations. If posible always place the appliance on a solid floor. 60 cm. IMPORTANT REMARK: This appliance is provided with a security device to avoid opening during the cycles. Open it only when absolutely necessary and wait 2 to 3 minutes after you have stopped the machine to give the safety device time to unlock. 4. SELECT THE TEMPERATURE Turn the dial clockwise to the desired temperature . 5. SELECT THE PROGRAM Turn the dial clockwise until the marker reaches the desired program. 6. START Check if: The door is properly closed. The drain hose is adequately positioned. [. . . ] * Run the draining program for a few seconds. This way you make sure no water at all remains in the appliance which could freeze and thus damage it and its surroundings. When you need to start the machine up again, make sure that the room temperature is above 0°C. EXTERNAL CLEANING Clean the exterior cabinet of the appliance with neutral soap and water only, and then dry thoroughly. CLEANING THE DISPENSER DRAWER AND THE RECESS Pull the drawer to remove (slightly at first till the stop, then pull hard). Replace the drawer. CLEANING THE DRAIN FILTER A clean filter is important for correct functioning of the washing machine, and it should therefore be cleaned regularly. [. . . ]