User manual ZANUSSI FLS422C

[. . . ] INSTRUCCIONES ­ MODE D'EMPLOI INSTRUCTIONS ­ MANUAL DE INSTRUÇÕES LAVADORAS AUTOMATICAS LAVE-LINGE WASHING MACHINES MÁQUINAS DE LAVAR A ROUPA FLS 422 C FLS 522 C CONTENTS Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking and installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transit security bars. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Unscrew and remove the three rear screws by means of a key. HYDRAULIC CONNECTION There should be a COLD WATER tap near the washing machine with a screwing on connection pipe of 3/4 gas for the water supply, a sink, a wash basin or a drainage system in the wall. Previously check if: -- -- it is not a hot water tap. If not, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. Have the permanent drainage system in the wall checked by a plumber. Place the enclosed rubber joint, delivered in a plastic bag together with the appliance (A) Fig. 6), at the very end of the inlet hose and carefully screw the pipe to the tap taking care not to damage the screwdrive and fix the nut well on to the end in order to avoid leaking. If necessary turn the hose adequately by unscrewing the nut at the rear of the appliance. 2. Lean the appliance back on the rear and fit one of the polystyrene angles between the appliance and the floor. Make sure the hoses are not squashed. Fig. Carefully remove the plastic bags on the right and the left, pulling them to the centre of the appliance. Now tighten the nut anew to avoid leaks. (Open the tap and asure that it does not leak and close it again. ) Place the discharging hose in a washbasin or sink with the aid of the bent piece delivered separately. The bent piece has to be entered into the tube's mouth in order to assure the support. Aforesaid piece allows the hose to be fixed to the wall by means of an opening on the upper part and that way the hose does not move and its falling is avoided. 4. Place the machine in an upright position and remove the three plastic bolts. Fig. "NO SPINNING" BUTTON Pressing this button before starting the intense washing program all spinnings will be excluded. The other steps of the program remain unchanged. 5. TEMPERATURE SELECTOR This control allows you to select the temperature of the washing cycle in accordance with the kind of clothes to be washed. Turn the control until the required temperature coincides with the marker. «Prewash» symbol shows the compartment for the prewash detergent. «Wash» symbol shows the compartment for the washing detergent. «smooth» symbol shows the compartment for the smoothing additives. «bleach» symbol shows the compartment for the bleaching additives. On the program table you will find the most apropriate temperature for each kind of washing. Selecting F any program can be run through with cold water. This will ensure a saving in electricity consumption. 6. PROGRAM SELECTOR To select the required program turn the control clockwise until the marker on the top coincides with the number of the required program (reference mark on the control panel). [. . . ] * Select a wash program and run for a few seconds. * Position the end of the drain hose in a bowl on the floor. * Run the draining program for a few seconds. This way you make sure now water at all remains in the appliance which could freeze and thus damage it and its surroundings. [. . . ]