User manual ZANUSSI PI44GCI/2C

[. . . ] Viale Bologna, 298 47100 FORLÌ (Italy) 3 WARNINGS - GAS HOBS It is most important that this instruction brochure should be kept together with the appliance for future consultation. If the appliance is sold or transferred to another person, ascertain that the brochure is also given, in order that the new user can be aware of the correct use of the machine and the relative warnings. THESE WARNINGS HAVE BEEN PREPARED FOR YOUR SAFETY AND FOR THAT OF OTHERS, WE THEREFORE REQUEST YOU TO READ THEM CAREFULLY BEFORE INSTALLING AND USING THE APPLIANCE. q q q q q q q q q q q q This appliance has been designed for use by adults. Take care, therefore, that children do not attempt to play with it. [. . . ] In models having a security device turn the corresponding switch in an anti-clockwise direction to the maximum position, press in fully and keep pressed for approximately 5 seconds until the security valve automatically maintains the flame alight. IMPORTANT If after a few attempts the burner does not ignite, check that the baffle and its cap are correctly positioned. To interrupt the supply of gas, turn the switch in a clockwise direction to the position « ». For a minor consumption of gas and a better efficiency it is advisable to use pans having a diameter suitable to the burners, as shown in the table. It is also advisable that, as soon as a liquid starts to boil you should lower the flame sufficiently to maintain simmering point. In case the burner flame accidentally goes out, close the command switch and try to ignite again after not less than 1 minute. During cooking, when using fats or oils, take particular care as they can, when over-heated, self-ignite. Minimum and maximum diametres of recipients which can be placed on the burners. Burner Rapid (large) Semi-rapid (medium) Auxiliary (small) Min. 240 mm 220 mm 160 mm FO 0252 6 MAINTENANCE AND CLEANING Before each operation electrically disconnect the appliance. Wash the enamelled parts with warm water and detergent, do not use abrasive products which could damage them; frequently wash the baffles of the burners with boiling water and detergent, taking care to remove all encrustrations; the parts in stainless steel should be rinsed well with water after use and dried with a soft cloth. The hob's enamelled grills can also be washed in the dishwasher. For persistent marks use normal, non-abrasive detergents or specific products which can easily be found in commerce. It is never advisable to use wire pads, steel wool or acids for cleaning. This system permits the total encumbrance of the hob plus the gas supply tube to be contained to a depth of 30 mm. A) Intake pipe with nut B) Adjustable joint C) Rigid metallic gas supply tube FO 0265 Fig. 2 IMPORTANT Upon completion of installation, always check: q that all the joints are completely sealed by using a soapy solution, never a flame; that the automatic ignition system is operating satisfactory on all burners, both individually and in combination. Fig. 1 q 8 ELECTRICAL CONNECTION The appliance is predisposed to function with a 230V monophase voltage tension. Connection must be carried out in conformity with the regulations and dispositions of the laws in force. Before connecting ensure that: - The limiter valve and the electrical mains can support the voltage of the appliance (see registration plate). - The power supply is correctly earthed according to the regulations in force. - The plug or omnipolar interrupter used can be easily reached once the appliance has been installed. Fit the cable with a plug suitable to the voltage and connect to an appropriate security socket. If a direct connection to the mains is required, an omnipolar interrupter with a minimum opening of 3mm between contacts, dimensioned to the voltage and corresponding to the regulations in force, should be interposed between the appliance and the supply. The yellow/green earth cable must not be interrupted by the interrupter. The brown coloured phase cable (situated at terminal "L" of the terminal box) must always be connected to the network phase. [. . . ] If the tap is of a type with the pin by-pass inside the bar (Fig. 6-8), it is sufficient to screw or unscrew according to the type of gas as indicated in the following paragraph. If the tap is of a type with a lateral by-pass (Fig. 8) it is necessary to detach the command panel by applying pressure to the lateral projection (Fig. [. . . ]