User manual ZANUSSI TH500W MKII

[. . . ] The cut-out device will reset itself when the fan motor has cooled significantly. It is dangerous to alter the specifications or modify this product in any way. When installed between adjoining wall cabinets the wall cabinets must not overhang the hob. If the room where the hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type. [. . . ] The filter should be replaced at least every three months or more frequently if the hood is used more than three hours per day. 6 To Remove/Replace the Charcoal Filter 1. Remove one filter at a time by placing one hand over the filter and releasing the spring retaining clip. Allow the filter to hinge back and then remove. 4. Worktop lighting If the fluorescent strip lamp fails to function first check to ensure that the pins are located into the holder. Replacing the strip light 1. Remove the lighting diffuser screws, through the end capping on the right hand side. Slide the diffuser to the left until the opposite end is free, then pull the diffuser down. Remove the fluorescent tube and replace with one of the same specification. Replace the cover and the retaining screws. 2. 3. 4. Replacing the strip light starter 1. Open the visor and remove the grease filter cassette. Unscrew the two fixing screws which secure the internal cover immediately in front of the lighting diffuser, on the inside edge of the casing. Lift the cover from the bottom to remove. Rotate the starter anti-clockwise, and replace with one of the identical type. 2. 3. 4. 7 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · Check the hood is connected to the electricity supply. · Check that the fan speed control is set to 1, 2 or 3. The cooker hood is not working effectively · The fan speed is set high enough for the task. · The kitchen is adequately vented to allow the entry of fresh air. · If set up for recirculation, check that the charcoal filter is still effective. · If set up for extraction, check that the ducting and outlets are not blocked. · The safety cut-out device has been tripped. · Tum off the hob and then wait for the device to reset. The cooker hood has switched off during operation If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and serial number. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. SERVICE AND SPARE PARTS If you require an engineer or wish to purchase spare parts contact your local Service Force Centre by telephoning: For general assistance with your appliance or for information on Zanussi products please contact our Customer Care Department. Customer Care Department, Zanussi 55-77 High Street Slough Berkshire SL1 1DZ Tel: 08705 727 727* * calls to this number may be recorded for training purposes. 08705 929929 Your telephone call will be routed to your local Service Force Centre. 8 PEACE OF MIND FOR TWENTY FOUR MONTHS STANDARD GUARANTEE CONDITIONS We, Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in appliance or any part there of is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: · · · · · The appliance has been correctly installed and used only on the electrical supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. [. . . ] Tighten the butterfly bracket screws, by rotating the screws clockwise. If further alignment of the cooker hood is required the lower section of the casing can be adjusted horizontally, backwards and forwards. 2. 3. 13 To adjust the lower casing 1. Loosen the two screws immediately in front and behind the butterfly bracket screws. Once the screws have been loosened the lower section of the hood can be moved backward and forward. 3. This will allow the alignment of the decor trim with the wall cabinet above. [. . . ]