User manual ZANUSSI TJ1043-A

[. . . ] Remove the 2 screws D then take out the part E situated inside the appliance (fig. Nota : you can unscrew screws, washers and spacers using a wrench. 5 kg 2, 5 kg 1 kg 850 mm 397 mm 600 mm Before each wash, make sure that : · the drain hose is correctly placed · the water tap is turned on (fully open) · the plug is in the wall socket · the on/off pusbutton is on the "off" position (pressed out) Fig. 5 D Your washing machine is ready to operate : · lift up the lid of the machine · open the drum with your two hands by pressing the button A and the two flapdoors till they disengage · introduce the laundry into the drum ; close the drum and the lid of the machine Be careful : before closing the lid of your machine, make sure that the drum flapdoors are correctly closed : - the two flapdoors fastened - the button A pressed out E A Be careful : when the machine is installed on carpeted floor, ensure that the carpet do not obstruct the openings, located at the base of the machine, which are provided for ventilation. If you want to keep the alignment of your appliance with the adjacent cupboards, you have the possibility to cut the crossbar holding the hoses located in the back of your washing machine (fig. [. . . ] 6 The detergent dispenser 1 2 3 prewash powder compartment ( ) main wash powder compartment ( ) softener compartment ( ) Pour the recommended quantities of detergent into the corresponding compartments. 1 2 3 Control panel TJ 1274 H JET SYSTEM XE 1200 650 A D F G 60° A B 60° B+XE C 40° 40° + 95° 40° + 60° H J 40° J+XE K 30° 40° + 60° 40° + 40° M N P 30° + 40° + 40° Q R S 1 Select the programme 2 Select the temperature 3 necessary Press the pushbuttons if 4 Press the pushbutton " " XE 1200 650 XE 1200 650 A · choose the programme according to the nature and the degree of soil of the laundry. · turn the timer knob clockwise to select the chosen programme. 60° · choose the temperature which corresponds to the chosen programme (see the programme table) according to the nature of the laundry and to the fastness of the colours. · Energy saving pushbutton " XE " : this pushbutton enables to save energy by limiting the water temperature to 60°C (temperature knob on "XE"). The other caracteristics of the programme remain unchanged. Spinning speed reduction " 1200 " : 650 By pressing this pushbutton, it allows to get a spinning speed of 650 rpm with the wash programmes for resistant laundry. Rinse pushbutton " ": This pushbutton allows to get more water for the rinses with the wash programmes for resistant laundry (cotton-linen). · The programme starts. The control lamp lights on. The products (see the "Washing guide" leaflet) Prewash and main wash powder compartment Follow the manufacturer's instructions for recommended quantities. If the water is soft, decrease the quantity. If the water is hard or if the laundry is very soiled or stained, increase the detergent quantity a little. For information regarding the degree of hardness in your area, enquire with your local authorities. 1 - Dismantling Electrical connection Before you plug the appliance into the wall socket, make sure that : · The supply voltage of the domestic wiring system does not fluctuate by more than 10% plus or minus from the value shown on the rating plate. · The meter, the fuses, the supply line and the wall socket are all suitable to carry the maximum load required by the washing machine (2, 3 kW). The existing safety rules call for the appliance to be connected to an efficient ground wire. The manufacturer disclaims any liability whatsoever if B this accident prevention rule is not complied with. directive n° 87-308 of 06. 1987 relative to radio interference suppression and with E. E. C. directive n° 73-23 relative to electrical safety. Turn the two screws round a quarter with a screwdriver or a coin in order to take away the detergent dispenser. Water connection · The end of the water inlet hose must be connected to a cold water tap having 3/4" gas thread spout or to a water tap having a quick-coupling connector after having introduced in the hose ring nut a rubber sealing washer also provided with the machine. · The curved end of the outlet hose should be inserted into a drain pipe not less than 70 cm and not more than 1, 0 m from floor level. Make sure that the drain hose is always safely secured so that it will not become loose or fall down from its position. The water should drain freely and consequently, the drain hose should not be chocked or placed in such a way as to obstruct the normal water flow. [. . . ] The water should drain freely and consequently, the drain hose should not be chocked or placed in such a way as to obstruct the normal water flow. If an extension is required, remember that it might cause a malfunction in the drain pump, particularly if the extension has a length in excess of 1 meter or if the diameter of the extension is smaller than the diameter of the original drain hose. Water pressure : minimum : 5 N/cm2 (0, 5 kg/cm2) - maximum : 80 N/cm2 (8 kg/cm2) The detergent dispenser is very easy to remove, you just have to slide it towards the top. Clean the detergent dispenser under runnnig water with a brush or a twisted rag. Positioning and levelling To enable the appliance to be moved with ease, it is provided with two fixed wheels located at the rear of the base. Level the appliance by screwing or by unscrewing the adjustable feet. Accurate levelling reduces vibrations, noises and displacement of the washing machine during operation. [. . . ]