User manual ZANUSSI TL862C

[. . . ] A B B C 90° 90° E-60° 60° COULEURS EXPRESS RINCAGES ESSORAGE LONG D F G 40° RESISTANTS TRES SALES H RESISTANTS SALES J COULEURS DELICATES K A SYNTHETIQUES ET MELANGES 60° 60° 40° 60° LAINE WOOLMARK RINCAGES ESSORAGE DELICAT M N P 40° 1 Select the programme 2 Select the temperature 3 if necessary Press the pushbuttons 4 Spinning speed variator PROGRAMMES TEMPERATURES °C ESSORAGE VARIABLE tr/min A · choose the programme according to the nature and the degree of soil of the laundry. · turn the timer knob clockwise to select the chosen programme. 60° · choose the temperature which corresponds to the chosen programme (see the programme table) according to the nature of the laundry and to the fastness of the colours. · Half load pushbutton " " : if pressed in at the beginning of a wash programme, it allows to wash economically small quantities of laundry, up to 2, 5 kg of resistant laundry (cotton-linen) and to 1 kg of delicate laundry (synthetics). This pushbutton cannot be used with the wool programme (M). [. . . ] · Energy saving pushbutton " " : this pushbutton enables to save energy by limiting the water temperature to 60°C (temperature knob on "E"). The other caracteristics of the programme remain unchanged. 850 450 · it allows the selection of a spinning speed from 300 to 850 rpm according the nature of the laundry and to your drying possibilities (cotton : from 450 to 850 rpm ; synthetics : from 300 to 450 rpm). 5 Press the pushbutton " " · The programme starts. The control lamp lights on. The products (see the "Washing guide" leaflet) Prewash and main wash powder compartment Follow the manufacturer's instructions for recommended quantities. If the water is soft, decrease the quantity. If the water is hard or if the laundry is very soiled or stained, increase the detergent quantity a little. For information regarding the degree of hardness in your area, enquire with your local authorities. Bleach You may use a bleach agent in all the washing programmes. However, make sure that the fabric withstands the treatment. Bleach is automatically washed down into the drum. On the back part and with a spanner, remove the two red loosened spacers (A) (fig. 3). The holes which are now visible must be closed with the plugs (B) provided with the appliance (fig. 4). Fig 2 Water connection · The end of the water inlet hose must be connected to a cold water tap having 3/4" gas thread spout or to a water tap having a quick-coupling connector after having introduced in the hose ring nut a rubber sealing washer also provided with the machine. · The curved end of the outlet hose should be inserted into a drain pipe not less than 70 cm and not more than 1, 0 m from floor level. Make sure that the drain hose is always safely secured so that it will not become loose or fall down from its position. The water should drain freely and consequently, the drain hose should not be chocked or placed in such a way as to obstruct the normal water flow. If an extension is required, remember that it might cause a malfunction in the drain pump, particularly if the extension has a length in excess of 1 meter or if the diameter of the extension is smaller than the diameter of the original drain hose. Water pressure : minimum : 5 N/cm2 (0, 5 kg/cm2) - maximum : 80 N/cm2 (8 kg/cm2) Fig 3 A 5. Please ensure that these parts have been removed from the machine and keep them in case of next transport (fig. 5). Fig 5 Fig 4 Positioning and levelling To enable the appliance to be moved with ease, it is provided with two fixed wheels located at the rear of the base. [. . . ] Water pressure : minimum : 5 N/cm2 (0, 5 kg/cm2) - maximum : 80 N/cm2 (8 kg/cm2) Fig 3 A 5. Please ensure that these parts have been removed from the machine and keep them in case of next transport (fig. 5). Fig 5 Fig 4 Positioning and levelling To enable the appliance to be moved with ease, it is provided with two fixed wheels located at the rear of the base. Level the appliance very carefully by adjusting the levelling feet located at the front of the base. Then tighten the lock nuts at the top of the feet, using a spanner. B Cleaning the drain filter Be careful : when the machine is installed on carpeted floor, ensure that the carpet do not obstruct the openings, located at the base of the machine, which are provided for ventilation. Fig 6 Fig. [. . . ]