User manual ZANUSSI WDI1215W

[. . . ] 6 Instructions for the User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically. electricity, In the absence of electricity ignition can occur without the electrical device; in this case, approach the burner with a flame, push the relevant knob down and turn it anti-clockwise until it reaches the maximum position. If the control knobs become difficult to turn, please contact your local Service Force Centre. 8 Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a flat bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table). Burner Large (rapid) Small (auxiliary) minimum diameter 180 mm 80 mm maximum diameter 260 mm 160 mm As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering. If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causing the handle to overheat. Carefully supervise cooking with fat or oil oil, since these types of foodstuff can result in a fire, if over-heated. The stainless steel can become tarnished if excessively heated. Therefore prolonged cooking with potstones, earthenware pans or cast-iron plates is inadvisable. Also, do not use aluminium foil to protect the top during use. Make sure pots do not protrude over the edges of the cooktop and that they are centrally positioned on the rings in order to obtain lower gas consumption. Do not place unstable or deformed pots on the rings: they could tip over or spill their contents, causing accidents. Pots must not enter the control zone. 9 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you from supply. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. 12 Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: Depth: Width: Depth: 290 mm 510 mm 270 mm 490 mm CUT OUT DIMENSIONS SUPPLY SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V~ 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse HEAT HEAT INPUT Rapid Burner 3. 0 kW Natural Gas (10239 BTU/HR) 2. 8 kW L. P. G. 15 The minimum distance combustible material or a cooker hood can be fitted above the hob is 650 mm. For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I. S 813 Current Edition Section 7- Permitted Locations of Appliance. Installation IMPOR TANT This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a registered competent person. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this instruction booklet be ignored. 16 On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. A) End of shaft with nut B) Washer C) Elbow Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i. e. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob. correctly ectly, It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. [. . . ] Procedure: 1) Re-ignite the burner and set to MIN. 3) To adjust, use a thin bladed screwdriver and turn the adjustment screw (see diagram) until the flame is steady and does not extinguish, when the knob is turned from MIN to MAX. Repeat this procedure for all burners. Minimum adjustment screw Pressur Testing essure Pr essur e Testing The pressure testing must be carried out on the burners. Proceed as follows: 1) Remove the pan supports and the burner caps and crowns. [. . . ]