User manual ZANUSSI ZC140T

[. . . ] Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings or these warnings contact the Customer Care Department. Prior to installation Check the appliance for transport damage. Under no circumstances should a damaged appliance be installed. [. . . ] Leave the appliance for approximately 4 hours for the correct temperature to be reached before placing food inside. F To Start the Appliance Thermostat Control The thermostat control knob situated inside the refrigerator regulates the temperature of the larder compartment. Thermostat control is marked from 1-5 the higher the number, the colder the setting. Position 0 Position 1 Position 5 - Off - minimum coldness - maximum coldness Hints for storage Below is the recommended storage positions for various food types: 1. Ready-cooked foods, convenience foods, fresh meat, cold cuts 2. Milk, dairy products, foods in dishes 3. Large bottles, drinks 6 Storage Shelves The variable shelves increase the usefulness of the fresh food compartment. The shelves can be rearranged by opening the door to 90°. The door shelves can also be rearranged to your requirements. Energy Saving Advice Do not install the cabinet close to sources of heat, such as a cooker, dishwasher or radiator. Locate the appliance in a cool well ventilated room and make sure that the air openings of the cabinet are not obstructed. Always leave warm food to cool down to room temperature before placing in the fridge. Try to avoid keeping the door open for long periods, or opening the door too frequently as warm air will enter the cabinet, and cause the compressor to switch on unnecessarily often. Check that the thermostat control knob is turned to the correct setting relative to ambient conditions. Set the thermostat control knob to a warmer position. Check nothing is preventing the door from closing. Check the door gasket is intact and clean. Check if the appliance stands stable (all four feet should be on the floor). Check the drain hole is not blocked (see 'Maintenance and Cleaning'). The temperature in the appliance is too high If after the above checks your appliance still does not operate correctly, contact your local Zanussi Service Force Centre. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made, as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Ser vice and Spar e P ar ts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning: 08705 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk Before calling out an engineer, please ensure you have read the details under the heading "Something Not Working. " When you contact the Service Force Centre you will need to give the following details: 1. Clear and concise details of the fault 4. The model and serial number of the appliance (found on the rating plate) 5. The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service calls. 9 Cus t omer Car e Depar tment For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www. zanussi. co. uk Customer Care Department Zanussi 55-77 High Street Slough Berkshire SL1 1DZ 08705 727727 (*) *calls to this number may be recorded for training purposes. Guar ant ee Conditions We Zanussi undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electrical supply stated on the rating plate. [. . . ] Level the appliance by adjusting the two adjustable feet (1) at the front of the appliance. If required the washer (2) can be removed. Door Reversal If required the opening direction of the door can be changed as follows: To reverse the bottom hinge assembly proceed as follows: Disconnect the appliance from the electricity supply. Tilt the appliance backwards, resting the top edge of the appliance on a stool or something similar. Unscrew the adjustable feet situated on both sides at the front (2 pieces). [. . . ]