User manual ZANUSSI ZDI4041B

[. . . ] You MUST read it carefully before installing or using the appliance. Installation q q Check your dishwasher for any transport damage. If your dishwasher is damaged, you should contact your supplier. For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way. Any electrical and plumbing work required to install this appliance should be carried out by a qualified and competent person. [. . . ] You are reminded of this by the salt indicator light on the control panel which comes on when the salt has finished. The salt indicator light on the control panel can remain illuminated for 2-6 hours after the salt has been replenished, assuming the dishwasher remains switched on. If you are using salts that take longer to dissolve then this can take longer. The function of the machine is not affected. Do not worry if water over flows from the unit when filling with salt, this is quite normal. Adjusting the dose According to the finish and drying results obtained, adjust the dose of rinse aid by means of the 6 position selector (position 1 minimum dosage, position 6 maximum dosage). Increase the dose if there are drops of water or lime spots on the dishes after washing. Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades. Top up the rinse aid when the indicator light on the control panel illuminates. 27 In daily use q Check if it's necessary to refill with dishwasher salt or rinse aid Load cutlery and dishes into the dishwasher. Select a wash programme suitable for the cutlery and dishes. Start the wash programme. Loading cutlery and dishes Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher. q q q q q Before loading the dishes, you should: - Remove large left-overs. - Soften remnants of burnt food in pans When loading the dishes and cutlery, please note: - Dishes and cutlery must not impede the rotation of the spray arms . - Load hollow items such as cups, glasses, pans, etc. Light items (plastic bowls etc. ) must be loaded in the upper basket and arranged so they do not move. In case that plates are loaded in the upper basket: load them starting from the rear positions of the basket; tilting them slightly forwards and avoiding the front positions near the door. Before closing the door, ensure that the spray arms can rotate freely. 29 Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position. Maximum height of the dishes in upper basket lower basket Use of detergent Only use detergents specifically designed for use in dishwashers. Using no more than the correct amount of detergent contributes to reducing pollution. Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. With upper basket raised With upper basket lowered 20 cm 24 cm 31 cm 27 cm Fill with detergent To move to the higher position proceed as follows: 1. Carefully lift both sides upwards until the mechanism is engaged and the basket is stable. If the lid is closed: press release button (1). Fill the detergent dispenser (2) with detergent. The marking indicates the dosing levels: 20 = approximately 20 g of detergent 30 = approximately 30 g of detergent Attention! Never lift or lower the basket on one side only When the basket is in the higher position you will not be able to use the cup rack(s). To lower the basket to the original position proceed as follows: 1. Carefully lift both sides upwards and then allow the mechanism to drop back down slowly, keeping hold of it. After loading your machine always close the door, as an open door can be a hazard. 3. All programmes with prewash need an additional detergent dose (5/10 g) that must be placed in the prewash detergent chamber (3). This detergent will take effect during the prewash phase. [. . . ] For other combinations of fault codes not described in the above chart will appear, please contact your local Service Force Centre. . . . there are problems when operating the dishwasher Fault Possible cause The dishwasher door has not been properly closed. The programme does not start The fuse has blown in the household fuse box. For dishwasher models with delay start option: Delay start has been selected. There is a whistling noise during washing The whistling is not a cause for concern. [. . . ]