User manual ZANUSSI ZDT5044 annexe 1

[. . . ] This information has been provided in the interest of your safety. You MUST read it carefully before installing or using the appliance. Installation q Check your dishwasher for any transport damage. If your dishwasher is damaged, you should contact your supplier. For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way. [. . . ] Do not worry if water over flows from the unit when filling with salt, this is quite normal. Only use branded rinse aid for dishwashers. Never fill the rinse aid dispenser with any other substances (e. g. dishwasher cleaning agent, liquid detergent). This would damage the appliance. Adjusting the dose According to the finish and drying results obtained, adjust the dose of rinse aid by means of the 6 position selector (position 1 minimum dosage, position 6 maximum dosage). Increase the dose if there are drops of water or lime spots on the dishes after washing. Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades. BR09 Top up the rinse aid when the indicator light on the control panel illuminates. 28 q If you are using dishwasher detergent that already contains rinse aid, the detergent including the rinse aid must be placed in the detergent compartment. In this case the rinse aid inflow must be deactivated in order to avoid a double dosage. Deactivation/activation of the inflow of rinse aid (The dishwasher must be switched off) When the inflow of rinse aid has been deactivated, also the rinse aid indicator light on the control panel is automatically deactivated. All programme selection push buttons indicator lights will illuminate (setting mode). If only one programme selection push button indicator light is illuminated, this means that a washing programme has been selected. The programme must be cancelled: press simultaneously the function push buttons 2 and 3 for about 2 seconds, the indicator light of the setted programme push button starts flashing for about 2 seconds. After about 2 seconds the indicator lights of all the programme selection push buttons will illuminate indicating that the setted programme has been cancelled and that the machine is now in setting mode. If the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing upwards. Mix spoons with other cutlery to prevent them from sticking together. For best results we recommend you to use the cutlery grid provided (if the size and dimensions of the cutlery allow it). UI76 With upper basket lowered To move to the higher position proceed as follows: 1. Carefully lift both sides upwards until the mechanism is engaged and the basket is stable. Attention! Never lift or lower the basket on one side only When the basket is in the higher position you will not be able to use the cup rack(s). RC09 The upper basket The upper basket is designed for plates (dessert plates, saucers, dinner plates of up to 24 cm in diameter), salad bowls, cups and glasses. Arrange items on and underneath the cup racks so that water can reach all surfaces. Glasses with long stems can be placed upside down in the cup racks. For taller items, the cup racks can be folded upwards. US75 Light items (plastic bowls etc. ) must be loaded in the upper basket and arranged so they do not move. To lower the basket to the original position proceed as follows: 1. Carefully lift both sides upwards and then allow the mechanism to drop back down slowly, keeping hold of it. After loading your machine always close the door, as an open door can be a hazard. Before closing the door, ensure that the spray arms can rotate freely. US74 31 Use of detergent Only use detergents specifically designed for use in dishwashers. Using no more then the correct amount of detergent contributes to reducing pollution. [. . . ] If the fault code reappears contact your local Service Force Centre. For other combinations of fault codes not described in the above chart will appear, please contact your local Service Force Centre. . . . there are problems when operating the dishwasher Fault Possible cause The dishwasher door has not been properly closed. The programme does not start The main plug is not plugged in. The fuse has blown in the household fuse box. [. . . ]