User manual ZANUSSI ZFC15/4RD

[. . . ] " Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. " This product should be serviced by an authorized Service Centre, and only genuine spare parts should be used. " It is dangerous to alter the specifications or modify this product in any way. " Care must be taken to ensure that the appliance does not stand on the electrical supply cable. [. . . ] Best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. For safety reasons, minimum ventilation must be as shown in Fig. 1: Appliance positioned under overhanging kitchen wall units (see Fig. Appliance positioned without overhanging kitchen units (see Fig. Attention: keep ventilation openings clear of obstruction. Two adjustable feet at the cabinet base allow accurate levelling of the appliance. 1 100 mm A 45° D060 Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/ 308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. A 10 mm B 10 mm NP004 Rear spacers The plastic bag containing all relevant documentation also contains two spacers to be fitted into special holes in the back of the appliance. Fit the spacers into the holes, taking care to ensure that the arrow (A) is positioned as shown in Figure. Then turn them through 45° (arrow (A) vertical) until they lock into place. Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. 33 Door reversibility Before carrying out the operations described below, pull out the mains plug from the wall socket. To carry out door reversal operate as follows: Remove the plastic cover (6) (which has a clip-in fitting) masking the bottom hinge; Remove bottom hinge (1); Slide out the lower door from middle hinge (2) and remove the latter; Slide out the upper door from pin (3), unscrew the latter and then screw it down into the hinge provided on the opposite side; Remove the two plugs, to reveal the holes for the hinge pivots, and remount them on the other side; Refit the upper door and the middle hinge on the opposite side; Refit the lower door and bottom hinge (1) on the opposite side, after having removed the plugs (7) and screws; these must then be refitted in the holes on the opposite side; Refit the plastic cover (6) on the bottom hinge. Warning: After having reversed the opening direction of the doors check that all the screws are properly tightened and that the magnetic seal adheres to the cabinet. If the ambient temperature is cold (i. e. [. . . ] After two or three hours, reload the previously removed food into the compartment. Important: A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. 37 MAINTENANCE Unplug the appliance before carrying out any maintenance operation. Warning This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians. Interior light The light bulb inside the refrigerator compartment can be reached as follows: " unscrew the light cover securing screws; " unhook the moving part by pressing it as shown in the figure. If the door is open and the light does not come on, check that the bulb is properly screwed in; if it still does not work, replace the bulb with one of the same power. [. . . ]