User manual ZANUSSI ZFV1006

[. . . ] WASHING MACHINE USER MANUAL ZFV1006 THE CONTENTS SECTION 1:BEFORE USING · · · · · · · Safety warnings Recommendations Removal of transportation screws Adjustment of feet Electrical connection Water supply connection Water drain connection SECTION 2:INSTALLATION SECTION 3:TECHNICAL SPECIFICATIONS SECTION 4:CONTROL PANEL · · · · · · · · · · · · · · Start/Pause button Function indicator lights Function buttons Spin speed selector Program knob Before washing Running the machine Water inlet filters Pump filter Detergent drawer Siphon plug The cabinet The drum Remove of your machine from lime SECTION 5:WASHING YOUR LAUNDRY SECTION 6:MAINTENANCE AND CLEANING SECTION 7: PRACTICAL INFORMATION SECTION 8:AVOIDING MINOR FAULTS SECTION 9:AUTOMATIC FAILURE DETECTION SYSTEM SECTION 10:INTERNATIONAL WASHING SIGNS 1 SECTION 1:BEFORE USING SAFETY WARNINGS · · · · · · · · · · · · · · · · Do not use a multiple socket or extension cord. Do not insert a plug with damaged or broken cord into the socket. If the cord is damaged it should be replaced by the manufacturer or appointed service agent in order to avoid a hazard. Never remove the plug from the socket by pulling from the cord section. [. . . ] Remove the filters found on the water inlet valves by using a pincer and wash thoroughly with a brush. Clean the filters of the water inlet hoses located on the tap side by removing manually together with the seal. After you clean the filters, you can fit them the same way as you have removed. PUMP FILTER The pump filter system elongates the life of your pump, which is used to drain the dirty water. Cleaning of your pump filter in every 2-3 months is recommended. To clean your pump filter: · Open the kickplate's cover, by pulling the handle. · Before opening the filter cover, place a cup in front of the filter cover to prevent flow of the remaining water in the machine. · Loosen the filter cover by rotating it counterclockwise and drain the water. · Remove the foreign materials from the filter. · Check for the rotation of the pump manually. · After you have cleaned the pump, fit the filter cover by rotating clockwise. · Put the kickplate cover into the place. · Do not forget that if you do not fit in the filter cover properly, it will leak water. 17 WARNING! Danger of being scalded!Since the water inside the pump maybe hot, wait for it to cool. DETERGENT DRAWER Detergents may form a sediment in your detergent drawer or in housing of the detergent drawer in time. To clean the sediment, pull out the detergent drawer from time to time. To pull out the detergentdrawer: · Pull the detergent drawer to the end. (DIAGRAM-1) · Lift the front of the drawer, continue to pull until the drawer is pull out. (DIAGRAM-2) · Wash will an old toothbrush and excessiveamount of water. · Take off the leftover detergent avoid to drop into your machine. · After drying the detergentdrawer put into the housing in the same manner you pull out. DIAGRAM-1 DIAGRAM-2 18 SIPHON PLUG Pull out the detrgent drawer. Remove the siphon plug and clean the residues of the softener thoroughly. Fit the cleaned siphon plug in its location. Check if it placed properly. THE CABINET Clean the exterior surface of the cabinet of your machine with lukewarm water and a cleaning substance that will not irritate the cabinet. After rinsing with clean water, wipe it with a soft and dry cloth. WARNING! If the machine is installed in a location where the ambient temperature can fall below 0 °C, do the following when it will not be in use: · Plug in the machine. · Close the water tap and pull out the water inlet hose or hoses from the tap. · Place the ends of the water drain and water inlet hoses in a cup on the ground. [. . . ] Distribution of the clothes in your machine is not wellbalanced. The end of the water drain hose is in a position too low according to the machine. The water is at the lower part of the drum. The pieces of some detergents which do not dissolve in water may stick to your clothes as white stains. METHODS OF ELIMINATION Put the clothes in your machine in a manner not to exceed its maximum capacity. [. . . ]