User manual ZANUSSI ZGF320X

[. . . ] Always insist on genuine Zanussi spare parts. Ensure that all control knobs are in the OFF position when not in use. Should you connect any electrical tool to a plug near this cooking appliance, ensure that electric cables are not in contact with it and keep them far enough from the heated parts of this appliance. If the appliance is out of order, disconnect it from the electric supply. MANUFACTURER: ELECTROLUX HOME PRODUCTS ITALY S. p. A. [. . . ] At the same time, turn the relevant control knob anticlockwise to maximum position and keep it pushed down for about 5 seconds. This will allow the "thermocouple" (Fig. D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. Then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" (Fig. To put the flame out, turn the knob to the symbol . · Always turn the flame down or put it out before taking the pans off the burner. Fig. 1 FO 0204 USING THE HOB CORRECTLY To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside). It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. A - Burner cap B - Burner crown C - Ignition candle D - Thermocouple Table of minimum and maximum diameters of pots which can be placed on the burners Burner Big (rapid) Small (Auxiliary) minimum diameter 180 mm. Cleaning and Maintenance · Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. Wash the enamelled components with warm soapy water. Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Electrical Connection The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label); 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit. The appliance is supplied with a connection cable. This has to be provided with a proper plug, able to support the load marked on the identification plate. To connect the plug to the cable, follow the recommendation given in Fig. The plug has to be fitted in a proper socket. If connecting the appliance directly to the electric system, it is necessary that you install a double pole switch between the appliance and the electricity supply, with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current rules. The connection cable has to be placed in order that, in each part, it cannot reach a temperature 90 °C higher than the room temperature. The brown coloured phase cable (fitted in the terminal block contact marked with "L") must always be connected to the network phase. [. . . ] Finally check the flame does not go out when quickly turning the knob from the maximum position to the minimum position. Table 1 : By-pass diameters Burner Ø By-pass in 1/100 of mm. 8 by-pass screw · This procedure can easily be carried out, anyhow the hob has been positioned or built in the working top. Auxiliary Rapid Table 2 : injectors BURNER NORMAL POWER kW REDUCED POWER kW NATURAL GAS G20 - 20 mbar inj. 1/100 Auxiliary (small) Rapid (big) 1 Natural gas : 3 LPG : 2, 8 0, 33 0, 65 70 119 m3/h 0, 095 0, 286 NORMAL POWER LPG 28-30/37 mbar inj. [. . . ]