User manual ZANUSSI ZGF681ICX

[. . . ] Do not spray areosols in the vicinity of this appliance while it is in operation. This hob should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. Service l Child Safety l l Environmental Information l l l l l The appliance is not intended for use by young children or infirm persons without supervision. This hob is designed to be operated by adults. Do not allow children to play near or with the hob. [. . . ] After cleaning, be sure to wipe dry with a soft cloth. FO 2237 Fig. 2 YES NO The Burners The burner caps and crowns (Fig. Wash the burner caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. Ignition candle The electric ignition is obtained through a ceramic "candle" and a metal electrode (Fig. Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed. Fig. 3 5 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM n There is no spark when lighting the gas SOLUTION u Check that the unit is plugged in and the electrical supply is switched on u Check that the RCCB has not tripped (if fitted) u Check the mains fuse has not blown u Check the burner cap and crown have been replaced correctly, e. g. after cleaning. n The gas ring burns unevenly u Check the main jet is not blocked and the burner crown is clear of food particles. u Check the burner cap and crown have been replaced correctly, e. g. after cleaning. Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your Service Centre. For your nearest Authorised Service Centre please contact: Electric Blue Service & Installation P/L 324 Frankston Dandenong Rd, Dandenong. VIC 3175 Phone: 1300 654 488 6 Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: Depth: CUT OUT DIMENSIONS Width: Depth: TYPE OF GAS TYPE OF BURNER SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner 580 mm. Electric: 230-240V 50Hz supply APPLIANCE GAS SUPPLY: Natural gas 1. 0 kPa - Universal LPG 2. 75 kPa 560 mm. 480 mm. NOZZLE NOMINAL MARKS GAS 1/100 mm CONSUMPTION MJ/h 1. 67 1. 11 0. 89 1. 02 0. 71 0. 55 13. 00 6. 80 3. 80 13. 00 6. 30 3. 60 NOMINAL PRESSURE kPa NATURAL GAS Double Crown (wok) Semi-rapid (medium) Auxiliary (small) Double Crown (wok) Semi-rapid (medium) Auxiliary (small) 1. 00 Burner Dia. Tap By-pass 1/100 mm U-LPG 2. 75 Auxiliary 28 Semi-rapid 35 Double crown 42 Aeration adjustment none Important safety requirements Location Choose a location free of draughts and open doors and clear of combustible materials or other fire hazards such as curtains, etc. The location should ensure convenience of operation and service. Any adjacent wall surface situated within 200mm from the edge of any hob burner and above the height of the hob must be a suitable noncombustible material for a height of 150 mm for the entire depth and width of the cooker. Any combustible material above the hotplate must be at least 650 mm above the top of the hob and no construction shall be within 450 mm above the top of the burner. must be left between the side edges of the hob and any adjacent cabinets or walls. 650 mm FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE 700 mm 400 mm 55 m mm 50 m 400 mm 100 mm 50 m m FO 0812 FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 600 mm 400 mm 50 m 55 m mm 400 mm 100 mm 50 m m FO 0813 7 Electrical connections The appliance is designed to be connected to 230-240 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label); 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit. The appliance is supplied with a connection cable provided with a plug, able to support the load marked on the identification plate. [. . . ] To avoid overhating, the building in should be carried out as shown in Figs. The hob's electric connection and the oven's one must be carried out separately, both for safety reasons and to allow the oven to be easily taken off the unit. Hanging forniture units or hoods must be placed at 650 mm. 9 480 30 60 a b 20 min 380 140 FO 2044 FO 2043 a) Removable panel b) Space possibly useful for connections Fig. [. . . ]