User manual ZANUSSI ZGF7899CX

[. . . ] Do not allow children to play near or with the appliance. The appliance gets hot when it is in use. Children should be kept away until it has cooled. Children can also injure themselves by pulling pans or pots off the hob. Service This appliance should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. Environmental Information After installation, please dispose of the packaging with due regard to safety and the environment. [. . . ] At the same time, keep the knob pushed down for about 5 seconds. This will allow the "thermocouple" (Fig. D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. Then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" and "crown" (Fig. To put the flame out, turn the knob to the symbol . When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically. To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). Burner Triple crown burner Large (rapid) Medium (semi-rapid) Small (auxiliary) minimum diameter 160 mm 160 mm 120 mm 80 mm maximum diameter 260 240 220 160 mm mm mm mm FO 0204 ABCD- Burner cap Burner crown Ignition electrode Thermocouple A B D C Fig. 1 5 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Pan Supports When washing the pan supports by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessay, remove stubborn stains using a paste cleaner. The Burners The burner caps and crowns can be removed for cleaning. Wash the burners taps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. Ignition electrode The electric ignition is obtained through a ceramic "electrode" and a metal electrode (fig. Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed. 6 Something Not Working? If the appliance is not working correctly, please carry out the following checks before contacting your local Service Centre. SYMPTOM There is no spark when lighting the gas SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e. g. Check the main jet is not blocked and the burner crown is clear of food particles. Check the burner cap and crown have been replaced correctly, e. g. after cleaning. The gas ring burns unevenly If after all these checks, your appliance still does not operate correctly, contact your local Service Centre. Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: Depth: Height: 680 mm 510 mm 85 mm Supply Connections Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-V 50 Hz supply, 3 core flexible cable with non rewireable plug. Appliance Gas supply: LPG 30 mbar Appliance Class: 3 Appliance category: I 3 CUT OUT DIMENSIONS Width: 560 mm Depth: 480 mm Thickness: 30 mm Burner Nominal Power LPG (Butane "A") kW kCal/h 814 1368 2095 3080 Nozzle 50 65 80 98 g/h 75 126 193 284 Diameter Tap. By-Pass 28 35 45 56 Feeding Pressure mbar (*) Auxiliary Semi-rapid Rapid Triple crown 0, 95 1, 60 2, 45 3, 60 30 (*) 1 mbar = 10 mm. [. . . ] 5 10 Electrical connections Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person, in accordance with the current regulations. The manufacturer declines any liability should these safety measures not be observed. This appliance is designed to be connected to a 230 V 50 Hz AC electrical supply. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label); 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit. [. . . ]