User manual ZANUSSI ZGF98CXE

[. . . ] Children should be kept away until it has cooled. Children can also injure themselves by pulling pans or pots off the hob. Environmental Information After installation, please dispose of the packaging with due regard to safety and the environment. When disposing of an old appliance, make it unusable, by cutting off the cable. The symbol on the product or on its packaging During Use This hob is intended for domestic cooking only. [. . . ] After cleaning, be sure to wipe dry with a soft cloth. YES Ignition electrode The electric ignition is obtained through a ceramic and metal electrode (Fig. Keep these components very clean, to avoid lighting difficulties, and check that the burner crown holes are not obstructed. Cast Iron Pan Supports The hob has cast iron pan supports. They are very heavy and could damage the hob or your kitchen furniture if you let them fall down. To keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. When removing the pan supports, lift them up as shown in the diagram. Never turn the pan supports on the hinges, this could damage them. Wash the pan supports using hot soapy water. If necessary, a paste cleaner or a soap impregnated steel wool pad can be used with caution. After cleaning, be sure to wipe dry with a soft cloth. NO 15 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM There is no spark when lighting the gas SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e. g. The gas ring burns unevenly Check the main jet is not blocked and the burner crown is clear of food particles. Check the burner cap and crown have been replaced correctly, e. g. If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Service and original spare parts This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention. For this reason we recommend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of the problem, the appliance model (Mod. ), the product number (Prod. No. ) marked on the identification plate. Original spareparts, certified by the product manufacturer and carrying this symbol are only available at our Service Centre and authorized spareparts shop 16 Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: Depth: 860 mm 510 mm Rear Left Burner (semi rapid) Heat Input 2. 0 kW Front Left Burner (auxiliary) Heat Input 1. 0 kW Rear Right Burner (semi rapid) Heat Input 2. 0 kW Front Right Burner (rapid) Heat Input 3. 0 kW Central Burner (Ultra-rapid Triple-crown) Heat Input 4. 0 kW CUT OUT DIMENSIONS Width: Depth: 830 mm 480 mm SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 220 V 50 Hz supply, 3 core flexible cable with non rewireable plug. VALUE = 37. 78 MJ/m3 CHARACTERISTICS Ws - 50. 7 MJ/ m3 TYPE OF GAS BURNER RAPID (large) MAX MIN SEMI-RAPID (medium) MAX MIN AUXILIARY (small) MAX MIN ULTRA-RAPID (triple-crown) MAX MIN POSITION NOMINAL THERMAL POWER kW NOMINAL FLOW RATE m3/h NOZZLE REFERENCE 1/100 mm NOMINAL THERMAL POWER kW NOMINAL FLOW RATE g/h NOZZLE REFERENCE 1/100 mm NATURAL GAS 20 mbar 3. 0 0. 65 2. 0 0. 45 1. 0 0. 33 4. 0 1. 2 0. 286 119 0. 062 Adjust. 0. 190 96 0. 043 Adjust. 0. 095 70 0. 031 Adjust. 0. 381 146 0. 114 Adjust. VALUE = 49. 92 MJ/Kg LPG GAS 28-30/37 mbar 2. 8 0. 65 2. 0 0. 45 1. 0 0. 33 4. 0 1. 2 202 86 47 40 144 71 32 32 72 50 24 28 288 98 86 56 Burner Auxiliary Semi-rapid Rapid Ultra-rapid Dia. Tap By-pass 1/100 mm 28 32 40 56 APPLIANCE CLASS : 3 APPLIANCE GAS SUPPLY: gas G28-30 / 37mbar Aeration adjustment none 17 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE 600 mm Provision for ventilation The hob should not be installed in a bed sitting room with a volume of less than 20 m3. If it is installed in a room of volume less than 5 m3 an air vent of effective area of 110 cm2 is required. If it is installed in a room of volume between 5 m3 and 10 m3 an air vent of effective area of 50 cm2 is required, while if the volume exceeds 11 m3 no air vent is required. [. . . ] The connection cable has to be placed in order that, in each part, it cannot reach a temperature of 90 °C. The brown coloured phase cable (fitted in the terminal block contact marked with "L") must always be connected to the network phase. Neutral Earth (yellow/green) 20 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2. Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3. [. . . ]