User manual ZANUSSI ZGG646ITN

[. . . ] Operating instuctions Gas hob ZGG 643 ZGG 646 Welcome to the world of Electrolux Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You find some examples on the cover in this manual. Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine. [. . . ] Prolonged cooking with potstones, earthenware pans or cast-iron plates is inadvisable. Also, do not use aluminium foil to protect the top during use. Make sure pots do not protrude over the edges of the cooktop and that they are centrally positioned on the rings in order to obtain lower gas consumption. Do not place unstable or deformed pots on the rings: they could tip over or spill their contents, causing accidents. If the control knobs become difficult to turn, please contact your local Service Force Centre. 8 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine. The pan supports The pan supports can be removed to easily clean the hob. After cleaning the hob, make sure the pan supports are correctly positioned. Pay attention when replacing the pan supports in order to avoid scratching the glass hob top. If washing the pan supports by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessary, remove stubborn stains using a paste cleaner. Fig. 2 The hob top Clean the hob while it is still warm. Never use aggressive or abrasive agents, such as oven sprays, stain or rust removers, scouring powders, or sponges with an abrasive effect. Special cleaning agents and ceramic hob scrapers are available from department stores. Slight, non-burnt soilage can be wiped off with a damp cloth. Burnt soilage has to be removed with a scraper. Afterwards wipe off the ceramic hob with a damp cloth. SYMPTOM There is no spark when lighting the gas. SOLUTION Check that the unit is plugged in and the electrical supply is switched on. Check that the general safety switch has not tripped (if fitted). Check the burner cap and crown have been replaced correctly, e. g. Check the main jet is not blocked and the burner crown is clear of food particles. Check the burner cap and crown have been replaced correctly, e. g. after cleaning. 11 Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: Depth: CUT OUT DIMENSIONS Width: Depth: APPLIANCE CLASS 3 580 mm 510 mm 550 mm 470 mm SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V ~ 50 Hz supply, 3 core flexible cable HEAT INPUT Rear Left Burner (semi rapid) Front Left Burner (rapid) Rear Right Burner (semi rapid) Front Right Burner (auxiliary) 1. 9 kW 2. 9 kW Natural gas 2. 7 kW Liquid gas 1. 9 kW 1. 0 kW APPLIANCE CATEGORY II2H3B/P GAS SUPPLY Natural gas G20 20 mbar 12 Table 1 : By-pass diameters Burner Ø By-pass in 1/100 of mm 28 32 42 Auxiliary Semi-rapid Rapid Table 2 : Injectors TYPE OF GAS BURNER INJECTORS 1/100 mm NORMAL POWER kW REDUCED POWER kW NORMAL POWER 3 m /h g/h FEEDING PRESSURE mbar NATURAL GAS LIQUID GAS Rapid Semi-rapid Auxiliary Rapid Semi-rapid Auxiliary Rapid Semi-rapid Auxiliary 119 96 70 86 71 50 120 105 80 2, 9 1, 9 1, 0 2, 7 1, 9 1, 0 1, 8 1, 4 0, 9 0, 75 0, 45 0, 33 0, 75 0, 45 0, 33 0, 75 0, 45 0, 33 0, 276 0, 181 0, 095 0, 191 0, 148 0, 095 196 138 73 - 20 30 NATURAL GAS * 13 * Injectors for natural gas G20 13 mbar are for Russia only 13 Instruction for the Installer The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. [. . . ] If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm. Hanging forniture units or hoods must be placed at 650 mm minimum from the hob. 18 Fitting the hob to the worktop Before fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge of the hob. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. 1) Remove the pan supports, the burners caps and crowns and turn the hob upside down, taking care the ignition candles are not damaged in this operation. [. . . ]