User manual ZANUSSI ZGG649ICN

[. . . ] Do not allow children to play near or with the appliance. The appliance gets hot when it is in use. Children should be kept away until it has cooled. Children can also injure themselves by pulling pans or pots off the hob. Service This appliance should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. During Use This appliance is intended for domestic cooking only. [. . . ] The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. Pan Supports The pan supports are dishwasher proof. If washing them by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessay, remove stubborn stains using a paste cleaner. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a cleaning product such as Hob Brite or Bar Keepers Friend is used. The Burners The burner caps and crowns can be removed for cleaning. Wash the burners taps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. 5 Something Not Working? If the appliance is not working correctly, please carry out the following checks before contacting your local Service Centre. SYMPTOM There is no spark when lighting the gas SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the burner cap and crown have been replaced correctly, e. g. after cleaning. The gas ring burns unevenly Check the main jet is not blocked and the burner crown is clear of food particles. Check the burner cap and crown have been replaced correctly, e. g. after cleaning. If after all these checks, your appliance still does not operate correctly, contact your local Service Centre. Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: Depth: Height: Weight: 580 mm. 9, 8 Kg. Supply Connections Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-V 50Hz supply, 3 core flexible cable with non rewireable plug. Appliance Gas supply: LPG 30 mbar Appliance Class: 3 Appliance category: I 3 CUT OUT DIMENSIONS Width: 550 mm. Thickness: 40 mm. Burner Nominal Power LPG (Butane "A") kW kCal/h 814 1368 2095 Nozzle 50 65 80 gh 75 126 193 Diameter Feeding Tap. By-Pass Tap colour Pressure mbar (*) 28 35 45 Red/Yellow Brown/Black Blue/Yellow 30 Auxiliary (dia. 90 mm. ) 0, 95 1, 60 2, 45 (*) 1 mbar = 10 mm. water coloumn. 6 Installation IMPORTANT This appliance must be installed by qualified personnel. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. Gas Connection On the end of the shaft (A) , which includes the GJ 1/2" threaded elbow, an adjustable joint is fixed so that the washer (B) is fitted between the components as shown in the diagram. A drop of paint at both edges of the "L" joint (C) will evidence that the good seal of the connection has been tested in the factory. Before connecting the gas supply pipe to the joint (C), the installer will ensure that the paint drop is unbroken and the "L" connector has not been moved by the vibrations during handling and transportation. When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob. FO 1010 A) End of shaft with nut B) Washer C) Adjustable joint Cut Out Size The dimensions of the cut-out are given in the diagram. Rectangular cut-out size for hob 0 51 0 58 55 0 47 0 55 mi n. FO 2106 7 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. Building over a kitchen unit with oven If the hob is built into a kitchen unit with an oven underneath, the recess must have the dimensions shown in diagrams 2 and 3, and should also incorporate suitable oven crosspiece supports to ansure an efficient cooling air circulation. [. . . ] Reassemble in reverse order. F: Remove Taps Ignition Switches (Isolate Electric Supply) 1. Disconnect the switches connector from the ignitor unit and remove the supply cables pulling the tabs connection off. Reassemble in reverse order and check with wiring diagram for correct reconnection. Technical Maintenance Check at regular intervals the condition and serviceability of the gas connection hose and pressure regulator, if any is fitted; in case of malfunction, do not repair but replace the whole faulty part. To ensure a smooth and safe operation, it is necessary to periodically grease the gas taps. [. . . ]