User manual ZANUSSI ZGM78ITX

[. . . ] Otherwise, contact your dealer before proceeding with the installation. The manufacturer disclaims any responsability should all the safety measures not be carried out. Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by unexperienced persons may cause injury or serious malfunctioning. [. . . ] Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a proper cleaning product is used. FO 2110 Candle for electric ignition The electric ignition is obtained through a ceramic "candle" and a metal electrode (Fig. 1 - lett. Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed. Periodic Maintenance Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated. l The periodic lubrication of the taps must be carried out by qualified personnel, which you must refer to also in case of malfunctioning. 4 Service and original spare parts This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention. For this reason we recommend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of the problem, the appliance model (Mod. ), the product number (Prod. No. ) marked on the identification plate. Original spareparts, certified by the product manufacturer and carrying this symbol are only available at our Service Centre and authorized spareparts shops. Technical Data Gas Burners Rating Ultra Rapid Burner (Triple crown) 4, 0 kW Rapid Burner (big) 3, 0 kW (G20) - 2, 8 kW (G30-G31) Semirapid Burner (medium) 2, 0 kW Auxiliary Burner (small) 1, 0 kW Class 3 Appliance Category II 2H3+ Setting Natural Gas G20 - 20 mbar Gas connection Electric Supply G 1/2" 230 V 50 Hz Hob recess dimensions Length Width 560 mm. 480 mm. 5 Instruction for the Installer l The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. l The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. l The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. l Avoid installing the appliance in the proximity of inflammable materials (e. g. curtains, tea towels etc. ). Gas Connection Choose fixed connections or use a flexible pipe in stainless steel. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. IMPORTANT - To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut G 1/2". Interpose the sealing between the components as shown in Fig. Screw the parts without forcing, adjust the connection in the required direction and tighten everything. A) Ramp with ending nut B) Seal C) Adjustable connection IMPORTANT - When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Use some soapy water, never a flame. FO 0264 Fig. 2 6 Electrical connection The appliance is designed to be connected to 230 V monophase electricity supply. [. . . ] Hanging forniture units or hoods must be placed at 650 mm. is fitted over the hob, the hanging forniture units beside the hood must be placed at 550 mm. minimum from the hob, to allow the fitting and the correct use of the lid, if required. Fig. 12 30 380 140 120 cm 2 180 cm 2 FO 2042 480 60 a b 20 min FO 2044 FO 2043 a) Removable panel b) Space possibly useful for connections Fig. [. . . ]