User manual ZANUSSI ZH6014W

[. . . ] 1. 7 - Never do flambé cooking under this cooker hood. 1. 8 - Never leave frying pans unattended during use as overheated fat and oil may catch fire. 1. 9 - Before carrying out any kind of maintenance or cleaning, disconnect the hood from the mains supply. 1. 10- If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then this must be of the room sealed or balanced flue type. [. . . ] When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0, 04 mbar to prevent fumes being drawn back into the room by the cooker hood. 1. 11- The appliance must be positioned so that the plug is accessible. 1. 12- If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. EN 4 4 INSTALLATION 2 - INSTALLATION INSTRUCTIONS Some installation systems require the opening and removal of the metal grille panel. 2. 1 - Instructions for opening and removing the metal grille panel To open the grille panel, press inwardly on the two slider catches at each side of the grille panel and the grille will pivot down. To remove the metal grille, pull forward on the right hand side so that the hinge pin on the back of the grille will be released from the slot in the side of the casing. 2. 2 - Wall cabinet fixing a - Predrilled wall cabinet: fix the hood onto the wall cabinet base panel using the four screws 4. 2 x 45 mm (supplied with the fixing kit). It is not necessary to open the metal grille. b - No predrilled wall cabinet: b. 1 - If the hood is provided with a paper fixing template, follow the instructions. b. 2 - If the hood is not provided with a paper fixing template, position the hood on the wall cabinet base panel and pilot drill the 3. 5 x 16 mm screws (not supplied with the fixing kit) from the inside onto the wood. 2. 3 - Wall mounting a - Drill two Ø 8 mm holes on the wall using the paper template, insert two rawl plugs and two 4. 2 x 44, 4 mm screws leaving 5 mm untightened. Open the metal grille panel, hook the hood on and fully tighten the screws. b - If the hood is not provided with a paper fixing template, drill two Ø 8 mm holes (see draw. ), insert the plugs and screws, proceeding as directed under paragraph a. c - For wall mounting using wallbrackets (optional), follow the instructions of the fixing template. It should not be washed and should be replaced every two months. If the filter is provided with a saturation indicator, replace when: b. 1-The violet colour of the dots, which are visible through the metal grille, is spread over the whole surface of the filter. b. 2-The red colour of the stripes, which is not visible through the metal grille when the filter is clean, becomes visible from the outside of the metal grille. It should be washed once a month in hot water using mild detergent or liquid soap. It should not be bent and should be left to drain dry. WARNING: An excess of grease in the filter not only would affect the performance of the hood, but it is also a possible fire risk. We strongly recommend therefore to clean and replace filters in accordance with the manufacturer instructions. 4. 2 - Cleaning Metal self- supporting Grease Filters · · · · The filters are washable and must be cleaned at least every 2 months of operation, or more frequently for particularly heavy usage. Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time. Wash the filters, taking care not to bend them. When refitting the filters, make sure that the handle is visible on the outside. 4. 3 - Charcoal filter The charcoal filter is a chemical filter to be used only when the hood is in the recycling position. [. . . ] When refitting the filters, make sure that the handle is visible on the outside. 4. 3 - Charcoal filter The charcoal filter is a chemical filter to be used only when the hood is in the recycling position. To replace the charcoal filter, open the grille and remove the thumb screw through the centre of the charcoal filter. If the filter is of the interlocking type, turn the filter anticlockwise. For a good performance replace the charcoal filter on average every three months. 4. 4 - Worktop illumination If a lamp fails to function at any time, open the metal grille panel and check that the lamp is fully screwed into the holder. [. . . ]