User manual ZANUSSI ZH6022BI

[. . . ] 89/336/CEE Cooker hood Dunstabzugshaube Hotte Wasemkap Cappa ZH 6022 ZH 9022 Operating instructions Bedienungsanleitung Mode d'emploi 4324142 - 01/98 Gebruiksaanwijzing Istruzioni per l'uso CONTENTS DESCRIBING THE COOKER HOOD IDENTIFICATION OF THE APPLIANCE PRODUCT SAFETY WARNINGS 1 5 7 9 DIMENSIONS SETTING UP AND INSTALLATION ELECTRICAL CONNECTION CONTROLS SWITCHING THE APPLIANCE ON AND OFF MAINTENANCE AND CLEANING 23 25 41 43 45 49 DESCRIBING THE COOKER HOOD This cooker hood features a through flow retractable visor which allows the hood to be installed inside a wall cabinet with the minimum loss of space while offering a large collection area for contaminated air once extended into its working position. The controls are located in a concealed control box which can be opened during use; the opening of the visor can be used to switch the appliance on when the controls have been pre-set. The cooker hood can be installed in two different ways: 1 2 RECIRCULATION MODE using charcoal filters to purify the contaminated air. EVACUATION MODE Using ducting to extract the contaminated air to the atmosphere. The grease filters are fitted to absorb grease and dust during cooking. [. . . ] Not following this warning could affect the safety of your cooker hood. 21 22 DIMENSIONS 23 24 SETTING UP AND INSTALLATION Before unpacking the cooker hood position the carton with arrows pointing upwards as illustrated. Remove the cooker hood and polystyrene side protection complete from the carton. Insert the ducting spigot into the aperture on the top of the cooker hood casing. Position the cooker hood upside-down, and ensuring the hood is supported correctly open the visor and remove the two metal grease filters or paper grease filter grilles. To remove the filters press inwardly on the actuator bolts at either side of the grille and remove. Cooker hoods in 60 cm are provided with 2 metal filters or grilles. 25 26 The cooker hood in 90 cm is provided with 4 grease filters which should be removed using the same method as for the 60 cm model. Cut a rectangular hole into the underside of the cabinet in accordance with the table below. MOD. 55 60 90 90 * A 453 503 803 503 B 162 162 162 162 A B * Special execution: cooker hood 90 cm with casing in 60 cm. Cut a round hole in the upper side of the cabinet aligning it with the air outlet of the cooker hood. 27 28 Insert the upper casing of the hood through the hole from the underside of the cabinet. If you wish to replace the factory fitted front strip with a personnalized strip remove the three screws. Remove the front strip. Drill the new front strip taking care to align it correctly. 29 30 Fix the new front strip with the screws provided. Fasten the screws of the butterfly quick fixing system. If necessary adjust the lower assembly horizontally by loosening the four screws and closing the visor. 31 32 Move the lower assembly as necessary to align the front with the cabinet door. Hold the hood body steady, open the visor and tighten the fixing screws. Fix the controls support to the underside of the cabinet using a provided screw. Now it is possible to install the cabinet to the wall. 33 34 The cooker hood can be installed in two different ways: RECIRCULATION FITTING: using cleansing charcoal filters to purify the contaminated air from cooking and to recirculate it back into the kitchen. DUCTING FITTING: (without cleansing charcoal filter) to pass contaminated air out through ducting to the atmosphere. RECIRCULATION FITTING: If the cooker hood is to be installed in the recirculation mode then charcoal filters must be provided. Insert che charcoal filters as illustrated ensuring that they click into position correctly. 35 36 Connect a suitable length of ducting to the air outlet on the top of the cooker hood inside the cabinet. The ducting should be long enough to project through the hole in the top of the cabinet. Fit the recirculation grille over the ducting and screw the grille to the top of the cabinet using the screws provided. Ensure that the blades in the grille are angled forwards as illustrated. Recycling installation is now completed. DUCTING FITTING When installed in the ducted mode the charcoal filters are not required. 37 38 To remove the charcoal filters press on the two charcoal filter catches and remove the filters as illustrated. Replace the metal grease filters or grease filter grilles. It is now possible to install the ducting. Care should be taken when selecting the ducting to ensure it is manufactured from a fire retardant material to National Standards. Attention should be taken when installing the ducting to choose the shortest possible run with the minimum number of bends. [. . . ] ATTENTION: For the models in 55cm widths it is also necessary to remove the internal cover when replacing the fluorescent strip lamp or the two lamps. 53 54 ATTENTION: Do not use hose pipes, pressure washers or cloths with a heavy concentration of water. Wipe the cooker hood over with a soft cloth wrung out in hot water and dry with a soft clean cloth. 55 56 [. . . ]