User manual ZANUSSI ZH9020W3

[. . . ] · The hood should not be used by children or persons not instructed in its correct use. MAINTENANCE · Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. · Clean and/or replace the Filters after the specified time period. · Clean the hood using a damp cloth and a neutral liquid detergent. GB 12 CHARACTERISTICS Dimensions GB 13 Components Ref. [. . . ] dia washers M6 nuts 12c 12c 1 Q. ty Documentation 1 Instruction Manual 12f GB 14 INSTALLATION Drilling the Ceiling/shelf and fixing the frame DRILLING THE CEILING/SHELF · Use a plumb line to mark the centre of the hob on the ceiling/support shelf. · Place the drilling template 21 provided on the ceiling/support shelf, making sure that the template is in the correct position by lining up the axes of the template with those of the hob. · Mark the centres of the holes in the template. · Drill the holes at the points marked: · For concrete ceilings, drill for plugs appropriate to the screw size. · For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm. · For wooden beam ceilings, drill according to the wood screws used. · For wooden shelf, drill ø 7 mm. · For the power supply cable feed, drill ø 10 mm. · For the air outlet (Ducted Version), drill according to the diameter of the external air exhaust duct connection. FIXING THE FRAME Before fixing, separate the Upper Section 2. 1 and the Lower Section 2. 2 from the Frame by unscrewing the screws 12c, then separate the two sections of the frame by unscrewing the 8 side screws to obtain the Upper frame and Lower frame. GB 15 Upper frame · Align the power supply cable feed hole · Fix the upper frame to the ceiling or shelf using: · For concrete ceilings, use the appropriate plugs for the screw size (not provided). · For hollow brick ceilings of wall thickness of approximately 20 mm: use 4 plugs 11 and 4 screws 12h (5, 2 x 70), provided. · Connect the control connector Cmd. · Place the connector in the junction box 24 and close it using the 2 screws 12e (2, 9 x 6, 5) 12e provided. · Fix the junction box to the hood body using the 2 screws 12c (2, 9 x 9, 5) provided. · For the recirculation version, fit the activated carbon odour filter. · Replace the grease filters. Cmd 12c 12c 8b 8a 12f 24 GB 17 USE Control panel L S V1 V2 V3 L S V1 V2 V3 Light Led Motor Speed Intensive Switches the lighting system on and off. Switches the extractor motor on and off at low speed. Used to provide a continuos and silent air change in the presence of light cooking vapours. Medium speed, suitable for most operating conditions given the optimum treated air flox/noise level ratio. Maximum speed, used for eliminating the highest cooking vapour emission, including long period. GB 18 MAINTENANCE Grease filters CLEANING METAL GREASE FILTERS · The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. · Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time. · Wash the filters, taking care not to bend them. [. . . ] · When refitting the filters, make sure that the handle is visible on the outside. Activated charcoal filter (Recirculation version) REPLACING THE ACTIVATED CHARCOAL FILTER · The filter is not washable and cannot be regenerated and must be replaced at least every 4 months of operation, or more frequently for particularly heavy usage. · Remove the metal grease filters · Remove the saturated activated carbon filter by releasing the fixing hooks · Fit the new filter by hooking it into its seating · Replace the metal grease filters. Lighting LIGHT REPLACEMENT 20 W halogen light. · Remove the 2 screws fixing the Lighting support, and pull it out of from the Hood. · Extract the lamp from the Support. [. . . ]