User manual ZANUSSI ZH959TN

[. . . ] · Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. · The hood should not be used by children or persons not instructed in its correct use. MAINTENANCE · Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. · Clean and/or replace the Filters after the specified time period. [. . . ] 1 Q. ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Telescopic Chimney comprising: 1 Upper Section 1 Lower Section 1 Right Air Outlet Grill 1 Left Air Outlet Grill 1 Reducer Flange ø 150-120 mm 1 Hood Body Air Outlet Extension Piece consisting of two Half Shells 2 Air Outlet Connection Extension 1 Air Outlet Connection 11 2. 1 2. 2 8a 8b 9 14 2 2. 1 2 8b 2. 2 12c 8a 14. 1 15 Ref. Q. ty Installation Components 7. 2. 1 2 Upper Chimney Section Fixing Brackets 11 6 Wall Plugs 12a 6 Screws 4, 2 x 44, 4 12c 6 Screws 2, 9 x 9, 5 Q. ty Documentation 1 Instruction Manual 1 Warranty 11 12a 1 GB 15 INSTALLATION Wall drilling and bracket fixing 1÷2 11 12a 650 min. 116 116 323 Wall marking: · Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. · Draw a horizontal line at 650 mm above the hob. Place bracket 7. 2. 1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. · Mark the wall at the centres of the holes in the bracket. · Place bracket 7. 2. 1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre (notch) with the vertical line. · Mark the wall at the centres of the holes in the bracket. · Mark a reference point as indicated at 116 mm from the vertical reference line and 323 mm above the horizontal reference line. · Repeat this operation on the other side. · Drill ø 8 mm holes at all the centre points marked. · Insert the wall plugs 11 in the holes. · Remove the filters by pushing them towards the back of the group and pulling down at the same time. · Wash the filters, taking care not to bend them. · When refitting the filters, make sure that the handle is visible on the outside. Activated charcoal filter (Recirculation version) REPLACING THE ACTIVATED CHARCOAL FILTER · This filter is not washable and cannot be regenerated, and must be replaced approximately every four months of operation, or more frequently with heavy usage. · Remove the metal grease filters. · Remove the saturated activated carbon filter by releasing the fixing hooks. · Fit the new filter by hooking it into its seating. · Replace the metal grease filters. Lighting LIGHT REPLACEMENT · 20 W halogen light. · Remove the 2 Screws fixing the Lighting support, and pull it out of from the Hood. · Extract the Lamp from the Support. · Replace with another of the same type, making sure that the two pins are properly inserted in the lamp holder socket holes. · Replace the Support, fixing it in place with the two Screws removed as above. GB 20 Quest'apparecchio é conforme alla norma europea sulla bassa tensione C. E. E. [. . . ] 89/336 relativa alla compatibilità elettromagnetica e C. E. E. This appliance complies with European regulations on low voltages, EEC Directive 73/23 on electrical safety, and with the following European regulations: EEC Directive 89/336 on electromagnetic compatibility and EEC Directive 93/68 on EC marking. Cet équipement est conforme à la norme européenne sur la basse tension C. E. E. 73/23 relative à la sécurité électrique et aux normes européennes: C. E. E. [. . . ]