User manual ZANUSSI ZHC590

[. . . ] INSTRUCTION BOOKLET COOKER HOOD ZHC 590 Thank you for buying a Zanussi product. To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Services Department. For general enquiries concerning your Zanussi appliance or for further information, visit our website at http://www. zanussi. co. uk Customer Services Department Major Appliances Zanussi Addington Way Luton Bedfordshire LU4 9QQ Tel: *Calls to this number may be recorded for training purposes. 08705 727 727* To register ownership, please ensure you complete and return the guarantee card supplied with the appliance. For the User Important Safety Information Your Appliance Operating Instructions Cooker Hood Controls To Operate Recirculation Extraction For the Installer Technical Information Electrical Connections Electrical Requirements Electrical Connection Installing the Cooker Hood Installation Requirements Unpacking Fitting the Wall Brackets Fitting the Canopy Hood Venting Recirculation Fitting the Chimney Stack Maintenance and Cleaning External Cleaning Metal Grease Filters Charcoal Filters To Remove/Replace Charcoal Filter Changing the Halogen Light Something Not Working Service and Spare Parts Guarantee Conditions The following Symbols will be found in the text to guide you through the instruction book Safety instructions Step by step instructions Guide to use the instruction book 2 IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety. [. . . ] The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. All service work under this guarantee must be undertaken by Zanussi Service Force Centre. (Electromagnetic compatibility) and subsequent modifications and Low Voltage directive 72/23/E. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. ELECTRICAL CONNECTIONS THIS APPLIANCE MUST BE EARTHED Electrical Requirements Any permanent electrical installation must comply with the latest I. E. E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). This appliance is fitted with a 3 core mains cable and must be permanently connected to the electricity supply via a double-pole switch having 3mm minimum contact gap on each pole. A Switched Fuse Connection Unit to BS1363 Part 4, fitted with a 3 Amp fuse, is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. This appliance conforms to BS 800: 1988 and EEC Directive No. 78 308 regarding suppression of radio and television interference. Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood. 11 INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas. This cooker hood is designed to be fixed to any orizontal surface over a cooking area, and can be used in the extraction (ducted to the outside) or recirculation mode. The installation work must be undertaken by a qualified and competent person. The manufacturer disclaims any responsibility for damage due to incorrect installation of the cooker hood or if the hood is not installed in compliance with relevant regulations controlling this type of installation. 14. 1 21 14. 2 Unpacking Before unpacking the cooker hood position the carton with the arrows pointing upwards as illustrated on the carton. The cooker hood is made up of the following components: Ref. Q. ty 1 1 2 7. 1 7. 1a 7. 1b 8 9 9a 14. 1 14. 2 15 25 1 1 1 1 1 1 1 1 1 1 2 Product Components Hood Body, complete with: Controls, Light, Blower, Filters Upper Chimney Telescopic frame complete with extractor, consisting of: Upper frame Lower frame Air Outlet Grill Reducer Flange ø 150-120 mm Ø120-125mm collar Air Outlet Connection Extension Air Outlet Extension Air Outlet Connection Pipe clamps Installation Components Screws M6 x 15 Drilling template Documentation Instruction Manual 15 7. 1a 14 25 9a 9 7. 1 7. 1b 2 Ref. [. . . ] · Push fit connector 15 onto the reducer flange. · Insert extension piece 14. 2 sideways into connector 15 making sure that the outlet corresponds with the mouth of the chimney 15 14. 2 9 16 INSTALLING THE COOKER HOOD Chimney Stack The chimney consists of two sections. The lower chimney measures (with the Hood body and recirculation grilles) 935 mm and the upper chimney measures 290 mm. The overall installed measurement is min. [. . . ]