User manual ZANUSSI ZHC604W

[. . . ] 12 AVVERTENZE PER LA SICUREZZA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Istruzioni per L'uso . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 MANUTENZIONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Filtro antigrasso in fibra sintetica . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] No. 1 splashback B (optional) · · B · Fig. 1 15 GB Installation instructions · · · · · For easy installation, proceed as follows: Fix the wall brackets and Splashback Fix the canopy Connect the hood to the mains power supply and make sure that it works properly Set the hood for ducting or recirculation Fix the telescopic chimney Fitting the wall brackets and Splashback · Draw a line on the wall up to the ceiling in the centre of the area where the hood is to be mounted. · Positioning brackets 1 Draw a horizontal like at a distance from the cooking appliance of: · with splashback (fig. 2) d = 93 + H, where H = height in millimetres from the visible part of the splashback; because of the various types of splashbacks available, this measurement must be taken directly on the splashback provided. On the horizontal line, mark the four holes for fixing the brackets 1 at a distance of 255 mm between the centre of the bracket holes and the hood centre. · Positioning brackets 2 · Rest one of the brackets 2 on the wall at about 1 or 2 mm from the ceiling or from the upper limit, aligning its centre (notches) on the vertical line. · Mark the two keyholes in the bracket on the wall. · Rest the other bracket 2 on the wall, aligning it to the vertical line at a distance X, measured as in fig. 2, which is the height of the upper chimney S supplied with the hood. Position X can vary according to the height of the upper chimney. · Mark the centres of the keyholes in the bracket on the wall. · Drill a hole with an Ø 8 mm bit on all the marked centres. 2 1 1 B B Fig. 2 16 GB · Splashback (optional) When a splashback is to be fitted, the distance between the hood and the cooking appliances will be determined by the height of the splashback B and whether or not there is a raised back on the worktop. The splashback is to be installed before installing the canopy. If the splashback is to be fixed to the wall using both the top and bottom fixing holes, care must be taken to ensure that the splashback is fitted at the correct height before fixing the base units or at least the worktop covering them. As this is a complex operation, it should only be undertaken by the technician installing the kitchen units or by a competent person who knows the final dimensions of the units. If the splashback is to be fixed through the top fixing holes only, proceed as follows: · Rest the splashback on the worktop and against the wall, as illustrated in fig. 2 . · Mark the centres of the two holes in the top surface. · Drill the wall using an 8 mm drill bit, and fix the splashback using the rawl plugs and screws provided. · If necessary, the installer should secure the splashback to the wall by tucking the bottom edge down behind the rear of the worktop. Fixing the canopy The hood can have two different fixing kits: a) screws, rawl plugs and safety brackets. b) screws, rawl plugs and metal brackets. · Fixing with screws: · Insert the rawl plugs in the holes 1, screw in the two screws provided (4. 2 x 44. 4) leaving about 5 mm unscrewed, hook the hood to the screws (fig. [. . . ] · Replacement · Open the grid panel, replace the charcoal filter by turning the locking handle anti-clockwise for removing and clockwise for replacing (fig. 17). ATTENTION - THERE COULD BE A POSSIBLE FIRE HAZARD IF THE FILTERS ARE NOT REPLACED ACCORDING TO THESE INSTRUCTIONS. Fig. 17 22 GB Lighting · It is composed of one or two 40 W lamps which can be reached by removing the grid panel (Fig. 18). · If the lights fail to function, check that they are fully screwed into place. [. . . ]