User manual ZANUSSI ZHC611W

[. . . ] 5 4 - INSTALLAZIONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4. 1 - Montaggio della staffa di supporto. Fondale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The manufacturer disclaims all liability for any damage or injury caused as a result of not following the instructions for installation contained in the following text. 2 - COMPONENTS The cooker hood is made up of the following components (fig 1): 2. 1 - n. 1 hood canopy C complete with controls, lighting and fan motor. 1 telescopic chimney stack formed by: n. 1 U-shaped lower section item I 2. 3 - n. 2 recirculation venting grilles item G (special versions only) 2. 4 - n. 1 deflector D (special versions only) 2. 7 - n. 1 additional recirculation spigot P (special versions only, see paragraph 4. 4 2 part 1a) 2. 8 - n. 1 wall brackets 1 to fix the canopy hood n. 2 wall brackets 2 to fix the chimney, rawl plugs, screws, and documentation 2. 9 - n. 1 splashback B (optional) 3 - SAFETY WARNINGS 3. 1- When used in the extraction mode the cooker hood ducting must not be connected to a flue which is used for exhausting fumes from appliances supplied with energy other than electric such as a central heating flue or water heating flue. 3. 2- Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood. This measurement should be determined by the height of the upper chimney stack and mark the centres for the keyhole bracket fixing screws. 4 - Pilot drill all the hole positions as marked on the wall using an 8 mm drill and fix the wall brackets 1-2 using the rawl plugs and screws supplied. 5 - Splashback (optional) When a splashback is to be fitted, the distance between the cooker hood and the cooking appliances will be determined by the height of the splashback, item F. The splashback is to be installed before installing the canopy. If the splashback is to be fixed to the wall using both the top and bottom fixing holes care must be taken to ensure that the splashback is fitted at the correct height before fixing it into position. The fitting should be undertaken by a a competent person with experience in this type of installation. If the splashback is to be fixed through only the top fixing holes proceeds as follows: a) Put the splashback on the worktop as illustrated in fig. 2a; then holding it against the wall to ensure that it is correctly positioned mark the holes for the top fixing screws on the wall. 11 b) Pilot drill the wall using an 8 mm drill and fix the splashback using the 8 mm rawl plugs and screws supplied. c) If the fixing holes in the bottom of the splashback are not to be used to secure the splashback to the wall the installer should ensure that the bottom edge is tucked down behind the rear of the worktop. 4. 2 - Fixing the canopy hood (fig. 3) 1234Adjust the two screws V (on the canopy connection points) to approximately half way. [. . . ] 13 3 - MAINTENANCE Regular maintenance and cleaning will ensure good performance and reliability, while extending the working life of the hood. Special attention should be paid to the grease filters and to the charcoal filters when the hood is used in the recirculation mode. 3. 1 - Metal grease filters 1 - Cleaning The metal grease filter should be cleaned every two months with normal usage and can be cleaned in a dishwasher or by hand using a mild detergent or liquid soap. 2 - Replacement Remove the filters one at a time, pushing the handle towards the rear of the hood (fig. When replacing, ensure that the handle faces outwards. 3. 2 - Thin synthetic filter On certain models the metal grease filters are replaced with a lower grille panel containing a paper grease filter with saturation indicators. [. . . ]