User manual ZANUSSI ZHC615X

[. . . ] MANUALE DI INSTALLAZIONE, USO E MANUTENZIONE INSTALLATION, USE AND MAINTENANCE HANDBOOK MANUEL D'INSTRUCTIONS POUR L'INSTALLATION, L'EMPLOI ET L'ENTRETIEN HANDBUCH FR INSTALLATION, BEDIENUNG UND WARTUNG INSTRUCTIES VOOR MONTAGE, GEBRUIK EN ONDERHOUD MANUAL DE INSTRUCCIONES, USO Y MANTENIMIENTO MANUAL DE INSTRUES, UTILIZAO E MANUTENO Parte 1 - ISTRUZIONI PER L'INSTALLAZIONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1 - GENERALIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 - COMPONENTI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 - AVVERTENZE PER LA SICUREZZA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 3. 2- Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood. 3. 3- Connect the cooker hood to the mains via a double pole switch which has 3 mm clearance between the contacts. 3. 5- When istalled, the hood must be positioned at least 65 cm above a cooking appliance. 3. 6- Never do flamb cooking under this cooker hood. 3. 7- Never leave frying pans unattended during use as overheated fats and oils may catch fire. 3. 8- Before carring out any kind of maintenance or cleaning, disconnect the hood from the mains supply. 3. 9- If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then this must be of the room sealed or balanced flue 10 type. If other types of flue or appliance are fitted en-sure that there is an adequate supply of air into the room. When the cooker hood is used in conjunction with other appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0, 04 mbar to prevent fumes being drawn back into the room by the cooker hood. 4 - INSTALLATION For easy installation proceed as follows: 4. 1 - Fix the wall brackets. 4. 3 - Connect the hood to the mains supply and ensure that it works properly. 4-4 - Set the hood for recirculation or evacuation. 4. 5 - Fix the telescopic metal frame. 4. 1 - Fixing the wall brackets (and splashback). Ref. 2a-b 1 - Draw a vertical line on the wall, from the centre of the cooking appliance up to the ceiling, using a marking pen. This is to ensure the correct vertical alignment of many components. 1: a) Put the bracket I to the wall, aligning its marked centre across the vertical line, ensuring that the distance between the centres of the holes and the cooking area is as follows: Draw a horizontal line on the wall ensuring that the distance from the cooktop is as follows: 1) when the splasback is to be installed: d = 265 mm + H, where H is the height of the visible part of the splashback; as the splashback can be of different heights, the correct H figure can only be obtained by measuring the actual height of the splashback to be fitted. 2) without splashback d = 915 mm minimum. Note: ensure that the wall bracket (I) is levelled. The hood can be aligned or adjusted in height by rotating the adjustment screws (see below). b) Mark on the wall the centres of the two keyholes of the bracket. 3 - Fixing the wall brackets item 2: a) Place one of the two brackets (item 2 fig. 1) 15 mm from the ceiling or from a horizontal line drawn between the top of the adjoining wall cabinets, ensuring that the bracket is level and mark the centres for the keyhole bracket fixing screws. b) Place the other wall bracket (item 2 fig. [. . . ] 1 - The paper filter visible through the perforated metal grille cannot be washed and should be replaced when the violet colour of the dots has spread over the whole surface and, in any case, not later than every 2 months. The manufacturer declines any liability for any injury or damage caused as a result of not following this instruction. 2 - Replacement - To remove the filter for subsequent replacement first open the metal grille panel (fig. 16a) by pressing back on the two slide catches towards the rear wall which will allow the grille panel to open and hinge downward from the rear. [. . . ]