User manual ZANUSSI ZHC71Y

[. . . ] Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Installation · Any installation work must be undertaken by a qualified electrician or a competent person. · This hood must be installed in accordance with the installation instructions and all measurements must be adhered to. · If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS. 6172, BS. 5440 and BS. 6891 (Natural Gas) and BS. 5482 (LP Gas) 1994, the Gas Safety (Installation & Use) Regulations, the Building Regulations issued by the Department of the Environment, the Building standards (Scotland) (Consolidated) Regulations issued by the Scottish Development Department. [. . . ] Rotate the charcoal filter anti-clockwise (A) and remove. To replace the charcoal filters, remove the metal grease filters. Place the filter over the inlet grille at either end of the fan housing and rotate clockwise (B) into position. This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. B A 3. 4. Changing the Light Bulb 1. Remove the screw fastening the lamp cover. Rotate the light bulb anti-clockwise to unscrew. To replace the light bulb insert a replacement into the holder then rotate the bulb clockwise into position. Ensure you take care not to overtighten the bulb. Replace the lamp cover. 4. If the light bulb fails to function check that the bulb is fully screwed into the holder. If bulb failure has occurred then it should be replaced with a 220-240 Volt 40W clear globe shaped bulb with a small E14 screw thread. Replacement filters and light bulbs can be obtained from your local Service Force Centre. 7 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · Check the hood is connected to the electricity supply. · The product is installed and used in accordance with our instructions and is only used domestically, i. e. Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden UK Senlis Nurnberg Pordenone Stockholm Slough +33 (0)3 44 62 22 22 +49 (0)911 323 2600 +39 (0)1678 47053 +46 (0)20 78 77 50 +44 (0)1753 219 897 9 INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical Information DIMENSIONS HEIGHT OF CANOPY: HEIGHT OF CHIMNEY: WIDTH OF CANOPY - ZHC 605: WIDTH OF CANOPY - ZHC 705: WIDTH OF CANOPY - ZHC 905: DEPTH OF CANOPY: GROSS - ZHC 605: GROSS - ZHC 705: GROSS - ZHC 905: NET - ZHC 605: NET - ZHC 705: NET - ZHC 905: VOLTAGE: POWER CONSUMPTION: FAN MOTOR: LIGHT BULB: (2 x 40 W) ELECTRIC HOB: GAS HOB: SLOT-IN GAS COOKER SLOT-IN ELECTRIC COOKER ELECTRICAL SUPPLY: 24cm (UPPER SECTION) 20cm (LOWER SECTION) 56cm 59, 8cm 69, 8cm 89, 8cm 49cm 16kg 16, 5kg 17, 6kg 12, 4kg 12, 8kg 13, 7kg 220-240 V 50Hz 230W 150W 80W 7KW (max) 10KW (max) 13. 5KW (max) 12. 4KW (max) SUITABLE FOR INSTALLATION ABOVE: Note: CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89:336. (Electromagnetic compatibility) and subsequent modifications and Low Voltage directive 72/23/E. ELECTRICAL CONNECTIONS DOUBLE INSULATED DO NOT EARTH Electrical Requirements Any permanent electrical installation must comply with the latest I. E. E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e. g. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer's installation instructions. A clearance height of 650mm (25 1/2 ") is required when installed above a built-in electric hob, or 700mm (27 1/2 ") when installed above a built-in gas hob. A clearance height of 685mm (27") is required when installed above a slot-in electric cooker, or 787mm (30 1/2 ") when installed above a slot-in gas cooker. [. . . ] · Mark the centres of the holes in the bracket. · Repeat this operation on the other side. SPLASHBACK (OPTIONAL) The Splashback must be fitted before fixing the hood body and, if it is to be fixed at both top and bottom, must be fitted at the correct height prior to installing the bases. As this operation is rather complex, it should be carried out either by the kitchen installer or a qualified person who knows the final dimensions of the units. [. . . ]