User manual ZANUSSI ZHC915W

[. . . ] 1 telescopic chimney stack formed by: n. 1 U-shaped lower section item I 2. 3 - n. 2 recirculation venting grilles item G (special versions only) 2. 4 - n. 1 reduction flange Ø 150-120 A 2. 5 - n. [. . . ] 5 - Splashback (optional) When a splashback is to be fitted, the distance between the cooker hood and the cooking appliances will be determined by the height of the splashback, item F. The splashback is to be installed before installing the canopy. If the splashback is to be fixed to the wall using both the top and bottom fixing holes care must be taken to ensure that the splashback is fitted at the correct height before fixing it into position. The fitting should be undertaken by a a competent person with experience in this type of installation. If the splashback is to be fixed through only the top fixing holes proceeds as follows: a) Put the splashback on the worktop as illustrated in fig. 2a; then holding it against the wall to ensure that it is correctly positioned mark the holes for the top fixing screws on the wall. 9 b) Pilot drill the wall using an 8 mm drill and fix the splashback using the 8 mm rawl plugs and screws supplied. c) If the fixing holes in the bottom of the splashback are not to be used to secure the splashback to the wall the installer should ensure that the bottom edge is tucked down behind the rear of the worktop. 4. 2 - Fixing the canopy hood (fig. 3) 1234Adjust the two screws V (on the canopy connection points) to approximately half way. Hook the rear of the canopy to the wall bracket 1, after anchoring the latter to the wall. Turn the screws V to adjust the canopy vertically and level it horizontally. Fit and lock the central fixing screw V1 (provided) to lock the canopy in place. 4. 3 - Electrical connection and working test 1 - The safety measures 3. 2, 3. 3 and 3. 4 of paragrapf 3 are to be strictly observed. 2 - Once the electrical connection has been completed, check that worktop illumination, motor and speed work properly. 4. 4 - Ducting or Recirculation fitting 1 - Ducting fitting a) The cooker hood can be ducted to the outside using either rigid or flexible fire retardant ducting of 120 or 150 mm. When 120 mm ducting is to be used it will be necessary to install the reduction flange item A on the air outlet fig. b) The installer should provide suitable ducting and sealing material for the installation. The cooker hood can also be ducted to the outside through one of the rectangular openings located in either side of the lower section of the chimney stack. In this case the deflector (item D) should be fitted into the spigot (item R) to close the aperture which is not used (fig. c) If the hood is provided with the charcoal filters fitted, the filters should be removed (see paragraph 3. 3 2 part 2a). 3 - Recirculation fitting a) The filtered air is returned to the room through the two side grilles on U-shaped lower section I, which are either formed in the metal itself (bottom position fig. 6), or as a plastic insert, and have two different heights to deal with different needs (bottom position fig. 6): fit the recirculation spigot item R into the round outlet on top of the canopy while pressing down on the spigot until it snaps into position. 7): fit the additional spigot, item P, into the round outlet on top of the canopy while pressing down on the spigot until it snaps into position. [. . . ] b) Pull the glass diffuser slightly to one side until it disconnects from the lug on the other side (arrow 1), then pull slightly downwards (arrow 2) and slide in the opposite direction (arrow 3) until the glass diffuser can be removed. Replace the lamps or the neon strip and replace the glass diffuser by repeating the above operations in reverse order. c) If illumination is provided by spotlights beside the control panel, these can be replaced simply by removing the metal grease filters. 2 - Halogen lamps a) Remove the metal lamp support in the same way as the glass diffuser (fig. [. . . ]