User manual ZANUSSI ZHC916X

[. . . ] INSTRUCTION BOOKLET COOKER HOOD ZHC 916X Thank you for buying a Zanussi product. To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Department. For general enquiries concerning your Zanussi appliance or for further information, visit our website at http:\\www. zanussi. co. uk Customer Care Department Zanussi 55-77 High Street Slough Berkshire SL1 1DZ * calls to this number may be recorded for training purposes. [. . . ] Visits may be available outside these hours in which case a premium will be charged. EXCLUSIONS This Guarantee does not cover: Damage or calls resulting from transportation, improper use or neglect, the replacement of any lilght bulbs or removable parts of glass or plastic. · Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United Kingdom. · Appliances found to be in use within a commercial environment, plus those which are the subject of rental agreements. · Products of Zanussi manufacture which are not marked by Zanussi. This guarantee is in addition to your statutory and legal rights. ZANUSSI EUROPEAN GUARANTEE If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: · The guarantee starts from the date you first purchased your product. · The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products. A Switched Fuse Connection Unit to BS1363 Part 4, fitted with a 3 Amp fuse, is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. This appliance conforms to BS 800: 1988 and EEC Directive No. 78 308 regarding suppression of radio and television interference. Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood. 10 INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas. The cooker hood is designed to be fixed to a solid block or brick wall over a cooking area. If not, suitable fixings must be used for other types of walls. The hood can be used in the extraction (ducted to the outside) or recirculation (internal recycling) mode. The Installation work must be undertaken by a qualified and competent person. The manufacturer disclaims any responsibility to damages due to incorrect installation of the cooker hood or if the cooker hood is not installed in compliance with relevant regulations controlling this type of installation. Unpacking Before unpacking the cooker hood position the carton with the arrows pointing upwards as illustrated on the carton. The ZHC916 is supplied with the following components for installation: 1 No. Canopy including controls and worktop illumination (C). Telescopic chimney stack complete with fan motor (A). Collar 120-125mm (D) Venting grille (G). Ducting conversion bend (W) Support Rod (B) S F G R W 11 INSTALLING THE COOKER HOOD Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, provided the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer's installation instructions. A clearance height of 650mm (25 1/2 ins) is required when installed above a built-in electric hob, or 700mm (27 1/2 ins) when installed above a built-in gas hob. A clearance height of 685mm (27 ins) is required when installed above a slot-in electric oven, or 787mm (30 1/ 2 ins) when installed above a slot-in gas oven. [. . . ] 4ab): - Remove the four screws fastening the plastic frame, as shown in Fig. 20) and replace the four screws removed as above. 16 17 18 19 20 16 INSTALLATION INSTRUCTIONS Fixing the chimney a) Loosen the screws M fixing the two parts of the chimney and pull the inner section I (Fig. Rest the lower section of the chimney in its housing on the top of the hood canopy. Lower the ducting fan unit until it reaches the wall bracket S and fix it using the screw H provided (Fig. [. . . ]