User manual ZANUSSI ZHC919X2

[. . . ] Exhaust hoods: connect the disposal duct to the air evacuation pipe of the hood; use a flexible pipe and lock it to the air evacuation pipe of the hood with a metal hose clamp (pipe and clamp are not provided). Make all power connections to the hood by means of the power cable. Take 2 assembled flues and place these on the upper surface of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2 screws (Fig. [. . . ] 8), fit the charcoal filter by turning anti-clockwise. - if the hood features a panel type charcoal filter (Fig. 9), remove the two metal filter retainers (M) and position the charcoal filter inside the grease filter; fit the two filter retainers back on again to secure the charcoal filter. OPERATION Depending on the model, the unit is equipped with the following controls: Controls shown in Fig. Button B = first speed motor ON/OFF switch. 11: A = Light switch; position 0: light off; position 1: light on. B = Motor switch; position 0: motor off; position 1-2-3: motor on at speed I, II and III. Button B = turns the TIMER on/off: press once to turn the timer on, therefore, after 5 minutes, the motor cuts out (at the same time the selected speed blinks on the display); the timer remains on if the motor speed is changed. Display C = - indicates the selected motor speed (from 1 to 4); - indicates Timer On when the number blinks; - indicates Filter Alarm when the central segments is on or blinking. Button D = makes the motor work (at the last speed selected); pushing the button again, the speeds of the motor are sequentially selected from 1 to 4; keeping this button pressed for about 2 seconds shuts down the motor. Button R = resets the grease filters or charcoal filters; when the filter alarm appears (i. e. when the central segment on the display goes on), the grease filters must be cleaned (30 hours of operation); when the central segment starts blinking, the grease filters must be cleaned and the charcoal filters replaced (120 hours of operation). For further information, see the Controls in Fig. 13 in the paragraph entitled "Operation". Charcoal filter/s: if using the hood in the filtering hood, the charcoal filter must be replaced periodically. To remove the charcoal filters, proceed as follows, depending on the model purchased: - if the hood features round charcoal filters (Fig. 14), remove the charcoal filter by turning clockwise. - if the hood features a panel type charcoal filter (Fig. 9), remove the charcoal filter by first of all removing the two filter retainers M. If the model purchased has the controls shown in Figure 12, the charcoal filters must be replaced whenever the central segment of the display starts blinking (i. e. If the model purchased has the controls shown in Figure 10/11, the charcoal filters must be replaced according to use: on the average once every 6 months. If the model purchased has the controls shown in Figure 13, the charcoal filters must be replaced each time the light button (Fig. 13S) lamp flashes (i. e. To gain access to the incandescence bulbs, remove the grease filters as described above and remove the bulbs. If the halogen lamps need changing, slacken the ring nut in an anticlockwise direction and remove the bulb itself (Fig. [. . . ] 1) werden die durch das Gerät geleitete Luft und der Dampf durch Kohlefilter gereinigt und dann über die seitlichen Lüftungsgitter der Haube wieder in Zirkulation gebracht. ACHTUNG: Bei Verwendung der Umluftversion sind ein Kohlefilter und ein Luftableitblech (A) notwendig, das in den unteren Teil des Rohrs eingebaut wird und ein erneutes Einleiten der Abluft in den Raum ermöglicht. Die Kohlefilter werden nicht mitgeliefert. 2) werden die Dämpfe und Küchengerüche direkt über eine Evakuationsöfffnung in der Wand oder Decke nach außen abgezogen. [. . . ]