User manual ZANUSSI ZHC923X

[. . . ] If the cut-out device is activated, switch off the fan motor and allow the cooker hood to cool. The cut-out device will reset itself when the fan motor has cooled significantly. It is dangerous to alter the specifications or modify this product in any way. When installed between adjoining wall cabinets the wall cabinets must not overhang the hob. [. . . ] This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Worktop Lighting The lamps should be replaced with a 230V 20W halogen spot lamp. To Replace the Lamps Unscrew the two screws to release the metal surround. Remove the lamp from the holder by pulling the lamp downwards. Replace the spot lamp with an identical replacement. When fitting the new lamp ensure the two pins are properly inserted into the slots in the lamp holder. Charcoal filters, grease filters and lamps can be obtained from your local Service Force Centre. 7 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · · · · · · · Check the hood is connected to the electricity supply. Make sure the switch is in the `ON' position. The fan speed is set high enough for the task. The kitchen is adequately vented to allow the entry of fresh air. If set up for recirculation, check that the charcoal filter is still effective. If set up for extraction, check that the ducting outlets are not blocked. The safety cut-out device has been tripped. Turn off the hob and then wait for the device to reset. The cooker hood has switched off during operation · · If after all these checks, the fault persists, contact your local Service Force Centre, quoting the model and serial number. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. SERVICE AND SPARE PARTS If you require an engineer or spare parts contact your local Service Force Centre by telephoning: For general assistance with your appliance or for further information on Zanussi products please contact our Customer Care Department. Customer Care Department Zanussi 55 - 77 High Street Slough Berkshire SL1 1DZ Telephone: 08705 727 727* * calls to this number may be recorded for training purposes. 08705 929929 Your telephone call will be routed to your local Service Force Centre. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk 8 GUARANTEE CONDITIONS We, Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in product or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: · · · · · The appliance has been correctly installed and used only on the electrical supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. Any appliance or defective part replaced shall become the property of this company. Home visits are made between 8. 30am and 5. 30pm Monday to Friday. Visits may be available outside these hours in which case a premium will be charged. EXCLUSIONS This Guarantee does not cover: · · · · Damage or calls resulting from transportation, improper use or neglect, the replacement of any lamps or removable parts of glass or plastic. Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United Kingdom. [. . . ] Insert the recirculation outlet extensions item 14. 4 into the recirculation adapter item 15. The recircualtion grilles item 8a and 8b must be fitted after the lower chimney item 2. 2 has been fitted. 15 8b 14. 1 8a 14 - Electrical Connection Connect the hood to the mains supply via a double-pole switch having a contact gap of at least 3mm. INSTALLING THE COOKER HOOD Fitting the Chimney Stack The chimney consists of two sections. The upper chimney measures 215mm and the lower chimney (with the holes for recirculation on either side) measures 740mm. - 7. 2. 1 Upper Chimney Stack Expand the sides of the upper chimney stack item 2. 1 and place the chimney over the two brackets 7. 2. 1 ensuring they are well seated. [. . . ]