User manual ZANUSSI ZHC945

[. . . ] INSTRUCTION BOOKLET COOKER HOOD ZHC945 Thank you for buying a Zanussi product. To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Department. For general enquiries concerning your Zanussi appliance or for further information, visit our website at http://www. zanussi. co. uk Customer Care Department Zanussi 55 - 77 High Street Slough Berkshire SL1 1DZ Tel: *Calls to this number may be recorded for training purposes. 08705 727727* To register ownership, please ensure you complete and return the guarantee card supplied with the appliance. For the User Important Safety Information For the Installer Technical Information Electrical Connections Your Appliance Operating Instructions Cooker Hood Controls To Operate Recirculation Extraction Electrical Requirements Electrical Connection Installing the Cooker Hood Installation Requirements Unpacking Fitting the Wall Brackets Fitting the Canopy Hood Venting Recirculation Fitting the Chimney Stack Maintenance and Cleaning External Cleaning Metal Grease Filters Charcoal Filters To Remove/Replace Charcoal Filter Changing the Halogen Light Something Not Working Service and Spare Parts Guarantee Conditions Guide to use the instruction book The following Symbols will be found in the text to guide you through the instruction book Safety instructions Step by step instructions 3 IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety. [. . . ] Restore the connection by pressing and holding T1. All five LEDs are turned on Within 3 seconds press T1 until LEDs T1 and T4 flash in confirmation: · LED flashes twice - Activated charcoal filter saturation alarm ENABLED · LED flashes once - Activated charcoal filter saturation alarm DISABLED The filter is not washable and cannot be regenerated. It must be replaced when led S1 flashes or at least every 4 months. The alarm signal will only light up when the extractor motor is switched on. To Remove/Replace the Charcoal Filters · Remove the metal grease filters · Remove the saturated activated carbon filter by releasing the fixing hooks · Fit the new filter by hooking it into its seating · Replace the metal grease filters. This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Alarm signal reset · Switch off the lights and extractor motor. · Press button T3 for at least 3 seconds, until the leds start to flash. Changing the Light halogen · Remove the snap-on lamp cover by levering it from under the metal ring, supporting it with one hand. · Remove the halogen lamp from the lamp holder by pulling gently. · Replace the lamp with a new one of the same type, making sure that you insert the two pins properly into the housings on the lamp holder. · Replace the snap-on lamp cover. Replacement filters and halogen light can be obtained from your local Service Force Centre. 9 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · Check the hood is connected to the electricity supply. · Make sure the switch is in the `ON' position. · The fan speed is set high enough for the task · The grease filter is clean. · The kitchen is adequately vented to allow the entry of fresh air. · If set up for recirculation, check that the charcoal filter is still effective. · If set up for extraction, check that the ducting and outlets are not blocked. · The safety cut-out device has been tripped. · Tum off the hob and then wait for the device to reset. The cooker hood is not working effectively The cooker hood has switched off during operation If after all these checks, the fault persists, contact your local Service Force Centre, quoting the model and serial number. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. SERVICE AND SPARE PARTS If you require an engineer or spare parts contact your local Service Force Centre by telephoning: For general assistance with your appliance or for further information on Zanussi products please contact our Customer Care Department. Customer Care Department, Zanussi 55 - 77 High Street Slough Berkshire SL1 1DZ Tel: 08705 727 727 * * calls to this number may be recorded for training purposes. 08705 929929 Your telephone call will be routed to your local Service Force Centre. The addresses are listed in the back of the book. 10 GUARANTEE CONDITIONS We Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: · · · · · The appliance has been correctly installed and used only on the electrical supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. All service work under this guarantee must be undertaken by Zanussi Service Force Centre. [. . . ] · Mark the wall at the centres of the holes in the bracket. · Mark a reference point as indicated at 116 mm from the vertical reference line and 306 mm above the horizontal reference line. · Repeat this operation on the other side. · Drill ø 8 mm holes at all the centre points marked. [. . . ]