User manual ZANUSSI ZHC9744X

[. . . ] Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. · · Installation Any installation work must be undertaken by a qualified electrician or a competent person. This hood must be installed in accordance with the installation instructions and all measurements must be adhered to. [. . . ] The charcoal filter cannot be cleaned or regenerated, and must be replaced approximately every 4 months, or more frequently if the hood is subjected to heavy usage. Replacing the charcoal filter First remove the metal grease filters. Remove the saturated activated charcoal filter by releasing the fixing hooks as illustrated. 5 Position the new charcoal filter in the position marked and while holding the filter replace the fixing hooks as illustrated. This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Changing the Spot Lamps Remove the two screws fixing the lighting support. Remove the spot lamp from the holder by pulling the lamp downwards. Replace the spot lamp by inserting the two pins at the base of the lamp into the holes in holder and pushing into position. Replace the lighting support, ensuring it is located correctly and fix back into position using the two screws. If one of the spot lamps has failed to function check that the lamp is fully seated into the lamp holder. If lamp failure has occurred then it should be replaced with a 12V 20W M262 halogen spot lamp. Replacement filters and lamps can be obtained from your local Service Force Centre. 6 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 1 32121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 1 321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 32121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · · · · · · · Check the hood is connected to the electricity supply. For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker This appliance is fitted with a 2 core mains cable and must be permanently connected to the electricity supply via a double-pole switch having 3mm minimum contact gap on each pole. A Switched Fuse Connection Unit to BS. 1363 Part 4, fitted with a 3 Amp fuse, is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. This appliance conforms to BS. 800:1988 and EEC Directive No. 78 308 regarding suppression of radio and television interference. 9 Unpacking The hood is supplied with the following components for installation as illustrated. Item Qty Description 1 1 Hood body, complete with: Controls, lighting, blower and filters 2 2. 1 2. 2 7. 1 7. 1a 7. 1b 8a 8b 9a 9b 14 14. 1 15 24 25 Item 12c 12e 12f 121 Item 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 Qty 6 2 4 1 Qty 1 Telescopic chimney comprising: Upper section Lower section Telescopic frame complete with extractor, consisting of: Upper frame Lower frame Right-hand air outlet grille Left-hand air outlet grille Ø120-125mm Ducting collar Ø150-120mm Ducting spigot Recirculation extension ducting Recirculation extension ducting Recirculation spigot Junction box Jubilee Clips Installation Components Ø2. 9 x9. 5mm Chimney fixing screws Ø2. 9 x6. 5mm Junction box fixing screws M6x10mm Hood body fixing screws Ceiling drilling template Documents Instruction Manual 10987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 1 1098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432 10987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 10987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 10987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 10987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 10987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 10987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 INSTALLING THE COOKER HOOD 21 23 22 7. 1a 12g 7. 1 11 12h 15 14. 1 14 7. 1b 12c 2. 1 2 2. 2 8b 8a 12e 24 9 25 12c 12c 1 12f 10 Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check that the wall to which the cooker hood is to be fitted for electric cables, water pipes and gas. This cooker hood is designed to be fixed to any vertical surface over a cooking area, and can be used in the extraction (ducted to the outside) or recirculation mode. The installation work must be undertaken by a qualified and competent person. The manufacturer disclaims any responsibility for damage due to incorrect installation of the cooker hood or if the hood is not installed in compliance with relevant regulations controlling this type of installation. Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications. [. . . ] 12 On completion check that the base is stable even if the frame is subject to movement. The installer must provide ample support where the ceiling or support shelf is not strong enough by installing cross beams over the joists or above the shelf to ensure the frame is quite rigid at its mounting point. Extraction The cooker hood is more effective when used in the extraction mode (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent of Ø125mm (5") or Ø150mm (6"). For the best performance use the shortest possible duct run and the minimum number of bends. [. . . ]