User manual ZANUSSI ZHI280W

[. . . ] If the room where the hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type. If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room. The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose. Do not install above a cooker with a high level grill. [. . . ] When the white paper inside the squares becomes saturated with grease the coloured dots start to run and spread across the paper, indicating that the filter has reached saturation point and must be replaced. To replace the synthetic paper grease filter 1. Press inwardly on the two slide catches and lower the grille to the stop position. Raise the front edge of the grille through a 45° angle until it detaches itself from the guides. Carefully ease out the metal wire retaining clips. Clean the metal grille and clips before replacing the grease filter. 3. 4. Handle the wire clips with care and keep away from children as they have sharp points. 6 The synthetic paper grease filter cannot be cleaned. It must not be washed. Charcoal Filter (for use in recirculation mode) The charcoal filter cannot be cleaned, it should be replaced approximately every three months or more often if the hood is used for more than three hours per day. To Remove the Charcoal Filter 1. Remove the thumb screw through the center of the charcoal filter, from the motor support. The charcoal filter can now be removed. 2. This appliance can be a fire hazard if the grease and charcoal filters are not replaced as recommended. Changing the Light Bulb The bulb should be replaced with a 220-240 volt 40 watt clear cylindrical shape bulb with a small (E14) screw thread. Replacement charcoal filters, grease filters and light bulbs can be obtained from your local Service Force Centre. 7 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · Check the hood is connected to the electricity supply. · Check that the fan speed control is set to 1, 2 or 3. The cooker hood is not working effectively · The fan speed is set high enough for the task. · The kitchen is adequately vented to allow the entry of fresh air. France Germany Italy Sweden UK Senlis Nurnberg Pordenone Stockholm Slough +33 (0)3 44 62 29 99 +49 (0)911 323 2600 +39 (0)1678 47053 +46 (0)8 738 79 50 +44 (0)1753 219 897 9 INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical Information DIMENSIONS HEIGHT: WIDTH: DEPTH: DEPTH WITH VISOR OPEN: GROSS: NET: Voltage (50Hz) 35 cm 60 cm 27-36 cm 54-63 cm 13, 0 kg 11, 0 kg 220-240 V 190 W 110 W 80 W WEIGHT ELECTRICAL SUPPLY: POWER CONSUMPTION: FAN MOTOR: LAMP: SUITABLE FOR INSTALLATION ABOVE: 2 x 40 W CHARCOAL FILTERS: ELECTRIC HOB: GAS HOB: SLOT-IN GAS COOKER SLOT-IN ELECTRIC COOKER Supplied 7 KW (max) 10 KW (max) 13. 5 KW (max) 12. 4 KW (max) Note: CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89:336. (Electromagnetic compatibility) and subsequent modifications and Low Voltage directive 72/23/E. ELECTRICAL CONNECTIONS WARNING: DOUBLE INSULATED DO NOT EARTH Electrical Requirements Any permanent electrical installation must comply with the latest I. E. E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). This appliance is fitted with a 2 core mains cable and must be permanently connected to the electricity supply via a double-pole switch having 3mm minimum contact gap on each pole. A Switched Fuse Connection Unit to BS1363 Part 4, fitted with a 3 Amp fuse, is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. This appliance conforms to BS 800: 1988 and EEC Directive No. If the height of the wall cabinet is less than 450mm, a gap of 50mm must be maintained either side of the hob. Hob A: Built-in Electric Hob: B: Built-in Gas hob: C: Slot-in Electric Cooker: D: Slot-in Gas Cooker: 650mm clearance 700mm clearance 685mm clearance 787mm clearance This cooker hood must not be installed above a cooking appliance with a high level grill. Unpacking The fittings supplied to install this cooker hood can be found with the instruction book inside the packaging. The fixing kit comprises: 2 - Wall fixing brackets 6 - Decor panel fixing screws 4 - Security fixing screws Fitting the Wall Brackets 1. Use the paper template provided to mark the hole positions on the wall for the bracket fixing screws (not supplied). Check the hole distances are correct with a tape measure as stated on the template. At this stage it is important to allow 15mm (1/2") clear space above the cooker hood to enable it to be hooked onto the brackets and for subsequent removal for decorating or servicing. 2. 3. 12 Venting The hood is more effective when used in the extraction setting (ducted to the outside). [. . . ] Use the 6 x 15mm (1/2 ins) round headed screws provided to attach the decor panel to the hood visor. 4. To Refit the Hood with Decor Panel Attached 1. Insert the upper visor guides into the upper track in the front of the casing. Hinge down the bottom edge of the visor and insert the lower guides into the track in the bottom of the casing. Push the visor in until an audible click is heard. [. . . ]