User manual ZANUSSI ZHP612N

[. . . ] · The hood should not be used by children or persons not instructed in its correct use. MAINTENANCE · Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. · Clean and/or replace the Filters after the specified time period. · Clean the hood using a damp cloth and a neutral liquid detergent. GB 3 33 CHARACTERISTICS Dimensions ø 120 280 L 0÷152 Hood Type L 45 448 50 498 55 548 60 598 70 698 80 798 175 90 898 Components 12e 8 12a 8 20 Ref. [. . . ] · Drill the support with a ø 4. 5 mm drill bit, using the drilling template provided. · Cut a hole ø 125 mm in size on the support surface, using the drilling template provided. · Fix using the 4 screws 12a (4, 2 x 44, 4) provided. 125 135 SNAP-ON FITTING · The hood can be installed either directly on the bottom surface of the wall units (min. 650 mm above the hob) using snap-on side supports. · Cut a fitted opening in the bottom surface of the wall unit, as shown. · Insert the hood until the side supports snap into place. · Lock in position by tightening the screws Vf from underneath the hood. Hood Type L1 45 352 50 402 55 452 60 502 70 602 80 702 90 802 12a 264 15 L1 Vf GB 5 55 CLOSING ELEMENT · The space between the edge of the hood and the rear wall can be closed by applying the element 20 provided, using the screws supplied for this purpose. 20 Connections RECIRCULATION VERSION AIR OUTLET · Cut a hole ø 125 mm in the wall unit over the hood. · Connect the hood body outlet to the top part of the wall unit using a rigid or flexible pipe ø120 mm, to be selected by the installer. · Fix the pipe in position using sufficient pipe clamps (not supplied). · Fix the directional grille 8 on the recirculation air outlet using the 2 screws 12e (2, 9 x 9, 5) provided. · Fit the new filters by hooking them into their seating. · Replace the metal grease filters, or close the filter retaining grill. Lighting LIGHT REPLACEMENT · 20 W halogen light. · Remove the 2 Screws fixing the Lighting support, and pull it out of from the Hood. · Extract the Lamp from the Support. · Replace with another of the same type, making sure that the two pins are properly inserted in the lamp holder socket holes. · Replace the Support, fixing it in place with the two Screws removed as above. · 40 W incandescent light · Remove the metal grease filters, or open the filter retaining grill. · Unscrew the bulbs and replace them with new ones having the same characteristics. · Replace the metal grease filters, or close the filter retaining grill. GB 9 9 Dir. 89/336/CEE 73/23/CEE 93/68/CEE The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. [. . . ] By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. auf dem Produkt oder seiner Verpackung weist darauf hin, dass dieses Produkt nicht als normaler Haushaltsabfall zu behandeln ist, Das Symbol sondern an einem Sammelpunkt für das Recycling von elektrischen und elektronischen Geräten abgegeben werden muss. Durch Ihren Beitrag zum korrekten Entsorgen dieses Produkts schützen Sie die Umwelt und die Gesundheit Ihrer Mitmenschen. [. . . ]