User manual ZANUSSI ZHT910W3

[. . . ] 7 Instruction for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Fasten the hood from inside the unit using four screws 4, 2 x 44, 4 (supplied)(fig. 7). · For suction hoods, the wall unit must be drilled to allow for the air discharge duct. · Filter hoods do not require this type of drilling operation since the air is recycled into the room through vents situated on the front of the hood. Fig. 5 401_05a Fig. 6 Fig. 7 GB 5 Connecting suction or filter hoods · Connecting suction hoods (Air is discharged into the atmosphere) The hood comes with two air outlets, a plastic cover fitted in the rear hole and a flange to be fitted according to the solution chosen:top discharge (fig. 8), rear discharge (fig. 9). In case of installation with rear discharge, fit the plastic cover in the top hole and the flange in the rear hole. Using a pipe Ø 100 o 120 mm, connect the air discharge flange to the external discharge duct. Open the grid panel by pressing inwards on the knobs (fig. 10), check that the lever (hood with one motor)or the handle (hood with two motors) points to the ducting mode position (fig. 11). Remove the charcoal filter, if any, by turning the handle anti-clockwise. Fig. 8 · · · · Fig. 9 Connecting filter hoods (Air is filtered and recirculated inside the room) · Open the grid panel. · Check that the lever (hood with one motor)or the handle (hood with two motors)points to the filter mode position (fig. 11) · Insert the charcoal filter. Electrical connection and working test · Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood. · Connect the cooker hood to the mains via a bipolar switch which has 3mm clearance between the contacts. · The device does not require earthing, as it is double-insulated. · Once the electrical connection has been completed, check that the worktop illumination, motor and speeds work properly. Fig. 10 Fig. 11 6 GB USE SAFETY WARNINGS · Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood. · The grease filters and the charcoal filters should be cleaned or replaced as recommended by the manufacturer or more frequently if the hood is used consistently (more than 4 hours per day). · When using a gas hob in connection with the cooker hood never leave the burners of the hob uncovered while the hood is in use or when the pans have been removed. Switch off the gas before removing the pan or for just short periods and never leave the hob unattended. [. . . ] WARNING : Respect replacement and maintenance schedules recommended in order to avoid fire hazards caused by over-saturated filters. Charcoal filters 1 - How they work Charcoal filters can absorb smells and odours until they are saturated. They cannot be washed or recycled and so they should be replaced at least every 4 months or more frequently if the hood is heavily used. [. . . ]