User manual ZANUSSI ZI5243

[. . . ] KÜHLSCHRÄNKE REFRIGERATEURS KOELKASTEN REFRIGERATORS ZI 5163 ZI 5193 ZI 5233 BEDIENUNGSANLEITUNG 2222 118-94 MODE D'EMPLOI GEBRUIKSAANWIJZING INSTRUCTION BOOKLET CONTENTS Warnings . Installation . GB . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page 31 32 32 32 32 32 33 34 34 34 34 34 35 35 35 36 36 36 37 37 37 37 37 Positioning . Electrical connection . Cleaning the interior . Instructions for totally built-in appliances Inner door reversal Use . . Operation . Temperature regulation . [. . . ] For operation with different voltages, a suitably sized auto-transformer must be used. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. min. 2 Push appliance into the housing until stop strip (A) touches the kitchen unit. D022 Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. Fig. 3 If after having carried out the previously A described operation there is still some space left between the appliance and the kitchen unit, fit the trimming D265 provided together with the appliance on the stop strip (A). 32 Fig. 4 Open the door and push the appliance against the side of the kitchen unit opposite to that of D appliance hinges. Fasten the appliance with 4 C screws provided D615 in the kit included with the appliance. Snap vent grille (C) and hinge cover (D) into position. 5 Press in the joint covers between the appliance and the kitchen unit. 8mm PR34 Fig. 8 Open both the appliance door and that of the kitchen unit to approx. Place the little plates over the runners. Hold the doors of the appliance and the unit together and mark the holes. D616 Fig. 6 Apply covers (B) on joint cover lugs and into hinge holes. Fig. 9 Remove the little plates and make the holes with a diam. Replace the little plates over the runners and screw in the screws provided (3. 5x16 mm). PR35 For the alignment of the kitchen unit door, if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. Inner door reversal Using a screwdriver release bracket (1) by pressing on the internal spring (Fig. [. . . ] No further food to be frozen should be added during this period; full, otherwise, it is recommended that the food should be used within a short time (a temperature increase of the frozen food shortens its safe storage period). Thawing Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, depending on the time available for this operation. Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking will take longer. The freezer compartment, however, will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. [. . . ]