User manual ZANUSSI ZI722/10DAC

[. . . ] KÜHLGEFRIERSCHRANK REFRIGERATEURCONGELATEUR TWEEDEURSKOELKAST FRIDGE-FREEZER ZI 722/9 DAC BEDIENUNGSANLEITUNG MODE D'EMPLOI GEBRUIKSAANWIJZING INSTRUCTION BOOKLET 2222 215-81 WARNINGS GB It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings. These warnings are provided in the interest of safety. You must read them carefully before installing or using the appliance. s General Safety s This appliance should be serviced by an authorized Service Centre, and only genuine spare parts should be used. [. . . ] 8 Position the runners (H) at the top and bottom of the inside of the kitchen unit as shown in Fig. and mark the position of the external holes. After preparing the holes, screw the runners to the kitchen unit door using 3. 5x16 mm screws. A 20m m 46 PR33 Open both the appliance door and that of the kitchen unit to approx. Place the little plates over the runners. Hold the doors of the appliance and the unit together and mark the holes. Fig. 9 8mm PR34 Remove the little plates and make the holes with a diam. Replace the little platee over the runners and screw in the screws provided (3. 5x16 mm). For the alignment of the kitchen unit door, if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. Fig. 10 PR35 If the appliance is fixed to the side of the kitchen unit, simply slacken the screws in the fixing brackets (G), move the brackets as shown in the figure and re-tighten the screws. Fig. 11 E D735 E Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. TECHNICAL SPECIFICATIONS The technical data is indicated in the rating plate on the left side inside the appliance. GB 47 USE GB This freezer has been marked with the symbol, which means that it is suited to the freezing of fresh foods, the conservation of frozen foods and the production of ice-cubes. The control panel 21 SN O 6 5 ABC A. Thermostat knob D E Internal thermometer This indicates the internal temperature of the freezer. It may indicate a temperature above 18°C when large quantities of food are placed inside for freezing or when the door is left open for a long time. Blue: normal Red: alarm -30 -18 °C 0 Starting Insert the power supply plug into the nearest wall socket (the function indicator light (A) will light up indicating that the freezer is receiving electrical input). Turn the thermostat knob (E) to the right to a medium setting (the temperature alarm light (C) will light up). For the satisfactory conservation of frozen foods, the freezer's internal temperature must be lower than -18°C. Wait until the temperature alarm light (C) turns off when the optimum temperature has been reached. Thermostat settings may be modified according to the surrounding room temperature, the location of the freezer and the frequency of door openings, etc. To turn off the freezer, turn the thermostat knob to the aO» position. The refrigerator compartment will remain operating. Freezing fresh food The 4-star compartment is suitable for long term storage of commercially frozen food, and for freezing fresh food. [. . . ] 18 D037 Defrosting Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates. The freezer compartment, however, will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 4 mm. [. . . ]