User manual ZANUSSI ZK23/9R

[. . . ] FRIDGE-FREEZER CHLADNICKA-MRAZÁK CHLODZIARKOZAMRAQARKA ZK 23/9 R INSTRUCTION BOOKLET NÁVOD NA INSTALACI A POU ËITI INSTRUKCJA OBSLUGI Å È 2222 045-57 CONTENTS Warnings . . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page 3 4 4 4 4 4 5 6 6 6 6 6 7 7 7 7 8 8 8 8 9 10 10 10 10 10 10 Positioning . Rear spacers . Electrical connection . Cleaning the appliance's interior . . Control panel Operation-Temperature adjustment. [. . . ] 87/308 of 2. 6. 87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. A 10 mm B 10 mm NP002 Rear spacers In the bag with the documentation, there are two spacers which must be fitted in the two top corners. Slacken the screws and insert the spacer under the screw head, then re-tighten the screws. Cleaning the appliance's interior Before using the appliance for the first time, wash all internal parts with lukewarm water and neutral soap so as to remove the typical «new» smell and then dry thoroughly. Do not use detergents or abrasive powders as these will damage the finish. 4 Door reversibility Before carrying out any operations, remove the plug from the power socket. To change the opening direction of the door, proceed as follows: 1. pull off the vontilation grille (D) which is clipped into place; 2. remove the hole cover (G) and the bottom hinge (E) by unscrewing its three fixing screws; 3. remove the lower door, sliding it out of the middle hinge; 4 unscrew the middle hinge (H); 5. remove the upper door, releasing it from the upper pin (G); 6 unscrew the upper pin (G) and refit it on the opposite side; 7. remove the two plugs of the door (where available), discovering the holes for the hinge pins, assemble them on the opposite side and refit the upper door; 8. reassemble the middle hinge on the opposite side; 9. using a 10 mm spanner, unscrew the hinge pin (E) and reassemble it on the opposite side of the hinge; 10. reassemble the lower hinge (E) on the opposite side, using the screws previously removed; insert the hole cover (G) on the lower hinge. Slide the hole cover (F) out of the ventilation grille (D) by pushing it in the direction of the arrow and reassemble it on the opposite side; 11. reassemble the lower door; 12. refit the ventilation grille (D), clipping it into place. To line up the doors, it is possible to adjust the middle hinge (H) horizontally by means of a toll, after slackening the two screws (see figure). Warning: After having reversed the opening direction of the doors check that all the screws are properly tightened and that the magnetic seal adheres to the cabinet. If the ambient temperature is cold (i. e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdrier. D419 D590 G H PR24 G E F E F F D F PR18 5 USE Control panel 4 3 A A. Thermostat knob B C Operation-Temperature adjustment Connect the plug to the wall socket. Start by using a medium setting and then, later, select the thermostat position most suitable for your requirements. The temperature is adjusted automatically and may be increased (warmer) by turning the knob towards the lower settings or may be decreased (colder) by turning it towards the higher settings. [. . . ] Small pieces of food ­ such as hamburgers, cutlets, chips, and fish fingers, for example ­ can be cooked straight from the freezer, without any intermediate thawing operation. Clearly, cooking time will be marginally longer than in the case of thawed food. Ice-cube production This appliance is equipped with trays for the production of ice-cubes. Fill these trays with water to 3/4 of their height, then put them in the freezer compartment. The ice-cubes may be shaken out from the trays by simply twisting; do not use metallic instruments to remove the trays from the freezer. 8 Defrosting Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. [. . . ]