User manual ZANUSSI ZKT 623 LX

[. . . ] plastic film, plastic, aluminium) on or near the appliance. How to avoid damage to the appliance · The glass ceramic can be damaged by objects falling onto it. · The edge of the glass ceramic can be damaged by being knocked by the cookware. · Cookware made of cast iron, cast aluminium or with damaged bottoms can scratch the glass ceramic if pushed across the surface. · Objects that melt and things that boil over can burn onto the glass ceramic and should be removed straightaway. [. . . ] Then a heat setting must be set for this cooking zone within 6 seconds, otherwise it must be re-selected. Setting the heat setting 3 After the sensorthe cooking zone, briefly reselecting lease field . Control field Increase Decrease Switch off Touch Touch Touch and at the same time Display ¾ to Ç Ç to ¾ ¾ 3 After 6 seconds with no input the selection is cancelled and the decimal point goes out. To set a new setting, select the required cooking zone again. 23 Using the child safety device The child safety device prevents unintentional use of the appliance. 3 To override the childsteps must be or switch it safety device off sucessfully, the performed immediately one after the other. No other sensor fields must be touched between the steps described. If the steps are performed in the wrong order, the display automatically switches itself off. Activating the child safety device Step 1. Control panel Switch on the appliance (Do not set a heat ¾ / h (if hot) setting) Touch of the front right cooking zone and at the same time Touch of the front right cooking zone 4 x ¾ or h Decimal points flash l Display Appliance switches off. Deactivating the child safety device Step 1. Control panel Switch on the appliance Touch of the front right cooking zone and at the same time Touch Display l / h (if hot) 4 x ¾ or h Decimal points flash Appliance switches off. Overriding the child safety device The child safety device can be released in this way for a single cooking session; it remains activated afterwards. Control panel Switch on the appliance Touch at the same time Display l / h (if hot) of the front right cooking zone and 4 x ¾ Decimal points flash Until the appliance is next switched off, it can used as normal. 24 Safety cut-out Cooking surface · If after switching on the appliance a heat setting is not set for a cooking zone within approx. 10 seconds, the appliance automatically switches itself off. · If one or more sensor fields are touched for longer than approx. 10 seconds, the cooking surface is automatically switched off. ER03 flashes on the display or changes to h if there is still residual heat. (Take out the fuse from the house's wiring system. ) If the fault is displayed again, please call the Customer Care Department and inform them of the fault code. If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department. 3 In the event of any other fault codes that arise, 1 Warning!Repairs to the appliance are only to be carried out by qualified service engineers. 3 If the appliance has been wrongly operated, Considerable danger to the user may result from improper repairs. the visit from the customer service technician or dealer may not take place free of charge, even during the warranty period. 29 Disposal 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e. g. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. 2 Old appliance The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. W 30 Installation Instructions Safety instructions The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc. ) Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed. A protective floor must be installed under the appliance. The cut surfaces of the worktop are to be protected against moisture using a suitable sealant. [. . . ] · Have the clamping joints correctedly installed by a qualified electrician. · Use strain relief clamp on cable. · In the event of single-phase or two-phase connection, the appropriate mains cable of type H05BB-F Tmax 90° (or higher) must be used. · If this appliance's mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90°; or higher). [. . . ]