User manual ZANUSSI ZKT 862LN

[. . . ] ENCIMERAS VITROCERAMICAS GLASKERAMIKKOCHFELD TABLE VITROCÉRAMIQUE KERAMISCH KOOKPLATEAU CERAMIC BUILT---IN HOB ZKT 862 LN / ZKT 862 LX GEBRAUCHSANWEISUNG NOTICE D'UTILISATION GEBRUIKSAANWIJZING CERAMIC BUILT---IN HOB INSTRUCCIONES PARA LA INSTALACIÓN, USO Y MANTENIMIENTO 319 620 300 2002. 09. mh--gw Dear Customer Congratulations on your purchase of an Zanussi glass--ceramic hob. You have thereby chosen in favour of quality and durability. These operating operations will help you become acquainted with your ceramic hob step--by--step, and enable you to take optimum advantage of all its features. You should, however, carefully read through the section «Important Safety Information» before putting the appliance into service for the first time. [. . . ] If you then switch to power level 4 (boost--6. 5 minutes), the heat--up time will continue for 6 minutes (6. 50 minus 0. 50). 13 + 5 Changing the power level with the decrease control (4) will switch off the automatic heat--up function. Take advantage of the residual heat by the Boost facility For saving energy make use of the residual heat by continuing cooking on a still hot cooking zone. This means the time for the boost facility will become shorter depending on the temperature of the still hot cooking zone. Switching off the Boost facility As soon as "A" appears in the Power Level indicator: 1. The cooking zone required must be activated. The dot (13) must be lit in the respective cooking zone. Press the decrease control (4). 13 -- 4 90 The Timer Function This function makes cooking easier for you. You don't have to remain close to the cooking zone throughout the whole cooking process: the cooking zone will be automatically switched off at the selected time. When no cooking zone has been programmed, the timer function can be used as an «egg--timer» (see «The Timer Function as an Egg--timer chapter»). Switching the Timer function on 1. The desired cooking zone must be activated. The dot (13) must be lit in the respective cooking zone. The timer display (8) now shows «00». Using the increase/decrease controls (5/4), enter the cooking time desired (01 to 99 minutes). The Timer function starts automatically after a few seconds. The control lamp (11) lights up at each cooking zone that has been programmed with the timer. To enter the cooking time more quickly, hold down either the increase or decrease controls (5/4) respectively. 5 8 11 7 Changing the set cooking time The cooking time can be subsequently changed where necessary: 1. The desired cooking zone must be activated The dot (13) must be lit in the respective cooking zone. Using the increase/decrease controls (5/4), select a new cooking time. To enter the cooking time more quickly, hold down either the increase/decrease controls (5/4) respectively. 4 13 Calling up the current cooking time -To call up the programmed cooking time remaining for the respective cooking zone, press the corresponding cooking zone key (2). 91 Switching the Timer function off When the programmed time expires . . an acoustic signal sounds for 2 minutes, and, at the same time the control lamp (11) of the timed--out cooking zone flashes (2 minutes). -To switch off the acoustic signal before the 2 minutes has expired, press any key. 11 The cooking zone is now switched off. . or if you want to switch the timer off early: 1. The desired cooking zone must be activated. The dot (13) must be lit in the respective cooking zone. [. . . ] The lateral separation between the sides of the hob and the cabinet must be at least 50 mm, and must be at least 50 mm from the rear panel. min. 50 mm 20 mm 20 mm · Fig. 1 This appliance conforms to Type Y (IEC 335- -6) -2with regard to fire protection. Only appliances of this type may be installed on one side of adjacent cabinets or walls. Installation 1. Cut out the worktop according to the prescribed dimensions (Fig. 1). [. . . ]