User manual ZANUSSI ZKT 862LX

[. . . ] Switching the power function on and off . 24 24 25 25 25 26 26 26 27 27 27 27 28 29 30 32 33 33 34 34 35 36 37 38 39 60 Installation Instructions . . 23 Operating Instructions 1 Safety instructions 3 Please comply with these instructions. If you do not, any damage resulting is not covered Directives: ­ 73/23/EEC dated 19. 02. 1973 Low Voltage Directive ­ 89/336/EEC dated 03. 05. 1989 EMC Directive inclusive of Amending Directive 92/31/EEC ­ 93/68/EEC dated 22. 07. 1993 CE Marking Directive Safety during use · Remove stickers and film from the glass ceramic. [. . . ] Control panel Switch on the appliance Touch and at the same time / acoustic signal Display/Signal Until the appliance is next switched off, it can used as normal. Releasing the child safety device Step 1. Control panel Switch on the appliance Touch Touch until the signal sounds Acoustic signal Display/Signal Appliance switches off. The child safety device is released. 28 Switching the power function on and off The power function makes additional power available to the front induction cooking zones, e. g. to bring a large volume of water to the boil. The power function is activated for 8 minutes for the front left cooking zone and for 5 minutes for the front right cooking zone. After these times, the induction cooking zones automatically return to cooking level . Control panel Switch on Switch off Touch Touch Touch Display 3 If the power function has ended, the cooking Power Management zones automatically switch back to the heat setting set previously. The cooking zones have a maximum power available to them. If this power range is exceeded by switching on the power function, Power Management reduces the heat setting of another cooking zone. The indicator for this cooking zone changes between the heat setting set and maximum possible heat setting for one minute. Thereafter the actual heat setting is displayed. Example: Last cooking switched on set heat setting zone Other cooking zone set heat setting indicator actual heat setting p 9 6 alternating with 9 6 29 Using the timer All cooking zones can use each use one of the two timer functions at the same time. Remove residues with water and washing up liquid. Cleaning the appliance after each use 1. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Removing deposits 1. Place a scraper on the glass ceramic surface at an angle. Remove residues by sliding the blade over the surface. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Remove Type of dirt sugar, food containing sugar plastics, tin foil limescale and water rings fat splashes shiny metallic discolorations immediately yes yes ------when the appliance has cooled down ----yes yes yes cleaner for glass ceramic or stainless steel* using a scraper* *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops 3 Remove stubborn residues with a cleaner for glass ceramic or stainless steel. 3 Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. 35 What to do if . . . Problem The appliance cannot be switched on or is not operating Possible cause Remedy More than 10 seconds have passed Switch the appliance on again. since the appliance was switched on The lock is switched on Switch off the lock (See the section "Locking/unlocking the control panel") The child safety device is switched Deactivate child safety device (See on the section "Child safety device") Several sensor fields were touched Only touch one sensor field at the same time Safety cut-out has been triggered Remove any objects (pan, cloths, etc. ) that are lying on the control panel. Switch the appliance on again The cooking zones automatically reduce the cooking level to The residual heat indicator is not displaying anything acoustic signal sounds, appliance switches off The sensor fields are partly covered Remove the cloth or the liquid. [. . . ] Anti-shock protection must be provided by the installation, for example drawers may only be installed with a protective floor directly underneath the appliance. The cut surfaces of the worktop are to be protected against moisture using a suitable sealant. The sealant seals the appliance to the work top with no gap. When building in, protect the underside of the appliance from steam and moisture, e. g. [. . . ]