User manual ZANUSSI ZKT621LX 63C

[. . . ] · For safety reasons, the cleaning of the appliance with steam jet or high-pressure cleaning equipment is not permitted. Correct use · This appliance should be used only for normal domestic cooking and frying of food. · The appliance must not be used as a work surface or as a storage surface. · Additions or modifications to the appliance are not permitted. · Do not place or store flammable liquids, highly inflammable materials or fusible objects (e. g. [. . . ] 10 seconds, the cooking surface is automatically switched off. ER03 flashes on the display or changes to h if there is still residual heat. · If all cooking zones are switched off, the cooking surface automatically switches itself off after approx. 10 seconds. Control panel 3 Moisture (e. g. a wet cloth) or liquid boiling over onto the control panel switches all cooking zones off. Cooking zones · If one of the cooking zones is not switched off after a certain time, or if the heat setting is not modified, the relevant cooking zone switches off automatically. Heat setting 1-2 3-4 5 6-9 6 hours 5 hours 4 hours 1. 5 hours Switches off after 25 Tips on Cooking and Frying 3 Information on acrylamides According to the latest scientific knowledge, intensive browning of food, especially in products containing starch, can constitute a health risk due to acrylamides. Therefore we recommend cooking at the lowest possible temperatures and not browning foods too much. Cookware · You can recognise good cookware from the bottoms of the pans. The bottom should be as thick and flat as possible. · Cookware made of enamelled steel or with aluminium or copper bottoms can leave discolorations on the glass ceramic surface which are difficult or impossible to remove. Energy saving 2 2 2 2 Always place cookware on the cooking zone before it is switched on. If possible, always place lids on the pans. Switch cooking zones off before the end of the cooking time, to take advantage of residual heat. Bottom of pans and cooking zones should be the same size. 26 Examples of cooking applications The information given in the following table is for guidance only. 3 Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. 28 What to do if . . . Problem The cooking zones are not functioning. Possible cause No cooking zone selected Remedy Select cooking zone within 10 seconds of switching on (Decimal point lights up) More than 10 seconds have passed Switch on the appliance again. The cooking zones cannot be selected / Appliance does not react to since the appliance was switched Select cooking zone within 10 seconds of switching on on the control panel input l The child safety device is activated Deactivate the child safety device (See section "Child safety device") The sensor fields are partly covered Remove the cloth or the liquid by a damp cloth or with liquid Safety cut-out has been triggered The residual heat indicator is not displaying anything Switch on the appliance again The cooking zone was only on for a If the cooking zone is supposed to short time and is therefore not hot be hot, call the Customer Service Department. Several sensor fields were touched Only touch one sensor field at the same time Safety cut-out due to overheating Let the appliance cool down. Disconnect the appliance from the electrical supply and have it connected properly Separate the appliance from the mains for a few minutes (remove the mains fuse). Let the appliance cool down. Er03 is displayed Er21 is displayed Er25 is displayed (only for 10 seconds) Appliance is incorrectly connected The overvoltage protector has been activated (for an incorrect connection see above Er25 or for overheating of the electronic components see Er21) Er40 is displayed disconnect the appliance from the electrical supply for a few seconds. (Take out the fuse from the house's wiring system. ) If the fault is displayed again, please call the Customer Care Department and inform them of the fault code. [. . . ] The latter is available from the Customer Care Department. A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm. Suitable isolation devices include line protecting cutouts, fuses (screw type fuses are to be removed from the holder), earth leakage trips and contactors. 1 IMPORTANT! 31 32 Service In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section "What to do if. . . "). If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. [. . . ]