User manual ZANUSSI ZKT641F 75G

[. . . ] frying chips) do not leave the appliance unattended. · Switch the cooking zones off after each use. 5 This appliance conforms with the following EU by the warranty. Correct use · This appliance should be used only for normal domestic cooking and frying of food. · The appliance must not be used as a work surface or as a storage surface. · Additions or modifications to the appliance are not permitted. [. . . ] · Cookware made of enamelled steel or with aluminium or copper bottoms can leave discolourations on the ceramic glass surface which are difficult or impossible to remove. Energy saving 2 2 2 2 Always place cookware on the cooking zone before it is switched on. If possible, always place lids on the pans. Switch cooking zones off before the end of the cooking time, to take advantage of residual heat. Remove residues by sliding the blade over the surface. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Remove Type of dirt sugar, food containing sugar plastics, tin foil limescale and water rings fat splashes shiny metallic discolorations immediately yes yes ------when the appliance has cooled down ----yes yes yes cleaner for glass ceramic or stainless steel* using a scraper* *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops, supermarkets, the parts department of your local Service Force Centre or from www. shop. electrolux. co. uk 3 Remove stubborn residues with a cleaner for glass ceramic or stainless steel. 3 Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. 12 What to do if . . . Problem The cooking zones are not functioning. Possible cause No cooking zone selected Remedy Select cooking zone within 10 seconds of switching on (Decimal point lights up) Switch on the appliance again. Select cooking zone within 10 seconds of switching on More than 10 seconds has passed The cooking zones cannot be selected / Appliance does not react to since the appliance was switched on the control panel input l The child safety device is activated Deactivate the child safety device (See section "Child safety device") The sensor fields are partly covered Remove the cloth or the liquid by a damp cloth or with liquid Safety cut-out has been triggered The residual heat indicator is not displaying anything Switch on the appliance again If the cooking zone is supposed to The cooking zone was only on for a be hot, call your local Service Force short time and is therefore not hot Centre. Several sensor fields were touched Only touch one sensor field at the same time Safety cut-out due to overheating. Disconnect the appliance from the electrical supply and have it connected properly Separate the appliance from the mains for a few minutes (remove the mains fuse). Let the appliance cool down. Er03 is displayed Er21 is displayed Er25 is displayed (only for 10 seconds) Appliance is incorrectly connected The overvoltage protector has been activated (for an incorrect connection see above Er25 or for overheating of the electronic components see Er21) Er40 is displayed disconnect the appliance from the electrical supply for a few seconds (Take out the fuse from the house's wiring system). If the fault code is displayed again, please call your local Service Force Centre and report the fault code. If you are unable to remedy the problem by following the above suggestions, please contact your local Service Force Centre. 3 In the event of any other fault codes that arise, 1 Warning!Repairs to the appliance are only to be carried out by qualified service engineers. 3 If the appliance has been wrongly operated, Considerable danger to the user may result from improper repairs. the visit from the service technician or dealer may not take place free of charge, even during the warranty period. 13 Disposal 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e. g. Please dispose of the packaging materials in the appropriate container at your local waste disposal facilities. 2 Old appliance The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. W 14 Installation Instructions Safety instructions The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc. ) Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed. A protective floor must be installed under the appliance. [. . . ] · Products of Zanussi manufacture which are not marketed by Zanussi. 21 Service and Spare Parts If the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning: 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk Before calling out an engineer, please ensure you have read the details under the heading , , What to do if. . . " When you contact the Service Force Centre you will need to give the following details: 1. The model and serial number of the appliance (found on the rating plate) 5. [. . . ]