User manual ZANUSSI ZL66W

[. . . ] REFRIGERATOR ZL 66 SI INSTRUCTION BOOKLET 2222633-74 Important Safety Instructions These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Prior to Installation ¥ Check the appliance for transport damage. Under no circumstance should a damaged appliance be installed. [. . . ] If the meat does drip, remove everything and clean thoroughly. ¥ Remove suspect food from your refrigerator and clean the interior (see ÒMaintenance and CleaningÓ). ¥ Never allow spillages to dry and harden. ¥ Store eggs in the egg rack provided in the refrigerator door. ¥ Regularly check the refrigerator door seal to ensure that it is clean and free from debris. ¥ Always wash your hands with soapy water and dry them with a clean towel before handling food. ¥ Keep work surfaces clean and avoid cross contamination by not using the same work surface or knife, without washing them thoroughly in between. Defrosting The refrigerator automatically defrosts every time the compressor stops. The water is discharged, via the pipe, into a tray located below the appliance, where it evaporates. Important To avoid defrost water overflowing into the fridge, periodically clean the water discharge hole in the centre of the V shaped drip collector at the back of the refrigerator compartment behind the fruit and vegetable drawers. Use the special cleaner provided which you will find already inserted into the discharge hole. D037 5 Maintenance and Cleaning Warning Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. Important This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians. Changing the light bulb Should the interior light fail to work, first switch off the appliance and disconnect from the electricity supply, then replace the bulb as follows: 1. Unscrew the light cover and then pull it outward by pressing as shown in the figure. Unscrew the bulb and replace it with a new 15 watt bulb (available from your nearest Service Force centre). Replace the light cover by sliding it into its original position and replacing the screw. Internal cleaning Clean the inside and accessories with warm water and bicarbonate of soda (5ml to 0. 5 litre of water). NEVER USE DETERGENTS, ABRASIVE POWDERS, HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES, TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND LEAVE A STRONG SMELL. Clean the drain hole of the water trough at regular intervals and make sure that the drain hole is never obstructed, so that the defrost water may flow freely. Important Do not use abrasive products. D411 When the appliance is not in use When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods and clean the appliance, leaving the door ajar to prevent unpleasant smells. External cleaning Wash the outer cabinet with warm soapy water. Once or twice a year dust the condenser (black grill) and the compressor at the back of the appliance, with a brush or vacuum cleaner, see the figure. You MUST ensure that the appliance is switched OFF. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk For Customer Service in Ireland please contact us at the address below: Zanussi Electrolux Electrolux Group (Irl) Ltd Long Mile Road Dublin 12 Republic of Ireland Tel: + 353 1 4090751 Email: service. eid@electrolux. ie Before calling out an engineer, please ensure you have read the details under the heading ÒSomething Not Working. Ó When you contact the Service Force Centre you will need to give the following details: 1. Clear and concise details of the fault 4. The model and serial number of the appliance (found on the rating plate) 5. [. . . ] When positioning the bottom hinge blade on the reverse side, the securing screws will require a degree of exersion when fitting. It is therefore advisable to lubricate the screw tips before starting this operation. Important After completion of the door reversal operation, verify that the door gasket is sealing onto the cabinet. If the ambient temperature is cold (i. e. [. . . ]