User manual ZANUSSI ZPL5163

[. . . ] Children should not be allowed to tamper with the controls or play with the product. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. This product should be serviced by an authorized Service Centre, and only genuine spare parts should be used. It is dangerous to alter the specifications or modify this product in any way. [. . . ] 1 Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. For building into kitchen units follow the special "Building-in" instructions given. Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. D243 Door reversal Right hand door opening Remove the upper and lower screws (1) and pivots (2) with the safety washer (4) on the left side (Fig. 3 3 Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. D562 6 4 5 32 Left hand door opening Remove the upper right screw and pivot. Straighten the safety washer (4) of the lower right hinge. Remove the screw (5) and the pivot (6) (Fig. For safety reasons bend the washer located under the left hinge (Fig. Remove the right door stop hinge (3-Fig. 4 Building-in Recess dimensions ZPL 5243 ZPL 5163-ZPL 5165 Height 1225 mm 880 mm Depth 550 mm 550 mm Width 560 mm 560 mm For safety reasons, minimum ventilation must be as shown in Fig. Attention: keep ventilation openings clear of obstruction. 50 mm 6 4 5 min. cm 200 2 D563 Fitting the handle Holes for fitting the handle on the opposite side are provided, with fixing screws already in place. D567 Inner door reversal (only for models ZPL 5243-ZPL 5163) Using a screwdriver release bracket (1) by pressing on the internal spring (Fig. 5) and withdraw it from its seat together with the door; remove plug (2) and fit it in the hole left open on the opposite side; Fig. [. . . ] Warning This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians. Interior light The light bulb inside the refrigerator compartment can be reached as follows: unscrew the light cover securing screws; unhook the moving part by pressing it as shown in the figure. If the door is open and the light does not come on, check that the bulb is properly screwed in; if it still does not work, replace the bulb with one of the same power. The maximum rating is shown on the light cover. 14 Periodic cleaning Never use metal objects for cleaning your appliance as it may get damaged. [. . . ]