User manual ZANUSSI ZR304CTN

[. . . ] FRIGORIFEROCONGELATORE FRIDGE-FREEZER KÜHL- UND GEFRIERSCHRANK REFRIGERATEURCONGELATEUR ZR 304 CTN LIBRETTO ISTRUZIONI 2222 239-28 INSTRUCTION BOOKLET GEBRAUCHSANWEISUNG MODE D'EMPLOI CONTENTS Warnings . . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page 11 12 12 12 12 12 12 13 14 14 15 15 15 15 16 16 16 16 17 17 17 17 18 18 18 18 18 Installation . . Installation of the appliance in a fitted kitchen unit Inner door reversal Use . . Instructions to assemble the refrigerator door to the kitchen unit door Operation - Temperature regulation. [. . . ] Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. D581 Building in Recess dimensions Height 1780 mm Depth 550 mm Width 560 mm To ensure adequate ventilation, allow the clearances shown in Fig. cm 2 200 D027 Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents which will leave an odour or abrasive powders on the interior, as these will damage the finish. 12 Installation of the appliance in a fitted kitchen unit (Fig. 3) Drill the unit using a Ø 2. 5 mm drill (10 mm max. Fix the square fitting (1) to the appliance and apply the rubber seal. If the door is not already assembled fix the square fitting (2) to the refrigerator and fitting (3) to the unit column. Fit the refrigerator into the space recessing it by 48 mm in relation to the unit base (Fig. Fix the refrigerator with the screws (5) to the upper and lower part of the unit, after having inserted the fittings (6) under the lower hinges. Fix the square fitting (1) to the unit column and the square fittings (2-3) to each other, after inserting the clip (4). 3 18mm 4 3 2 13mm 28mm 5 1 Ø 2, 5 5 5 6 Fig. 4 48mm D583 13 Instructions to assemble the refrigerator door to the kitchen unit door Position the runners (C) at the top and bottom of the inside of the kitchen unit as shown in Fig. 5 and mark the position of the external holes. After preparing the holes, screw the runners to the kitchen unit door using 3. 5x16 mm screws. 5 Remove the little plates and make the holes with a diam. Replace the little plates over the runners and screw in the screws provided (3. 5x16 mm). For the alignment of the kitchen unit door, if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. 7 C 20m m D135 Open both the appliance door and that of the kitchen unit to approx. Place the little plates over the runners. Hold the doors of the appliance and the unit together and mark the holes. 6 8mm PR35 Inner door reversal Using a screwdriver, release bracket (1). [. . . ] Fill these trays with water, then put them in the freezer compartment. Do not use metallic instruments to remove the trays from the freezer. Freezer compartment defrosting The air humidity that penetrates inside the appliance when opening its door, accumulates on the evaporator and particularly on its upper part, thus creating a layer of frost. To avoid excessive formation of frost do not leave the door open more than necessary. The formation of a thin layer of frost (as for example on the front edge of the freezer) does not require complete defrosting. [. . . ]