User manual ZANUSSI ZRC34SD

[. . . ] Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or more serious malfunctioning. Refer to your local Service Centre, and always insist on genuine spare parts. This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials; it must nevertheless be disposed off in a proper manner, in accordance with regulations for protection of the environment. This appliance is designed to be operated by adults. [. . . ] It is advisable to wait at least two hours before connecting the appliance to allow the oil to flow back in the compressor. 10 INSTALLATION If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. This will prevent it from becoming a death-trap for a child. Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Best performance is obtained with ambient temperature between +16°C and +32°C (class N) or between +10°C and +32°C (class SN). Secure the bracket with the screws supplied. Take care not to damage the front face of the panel whilst working. 10 Check the position again by slackening the screws and pins then, once the best position has been obtained, fully tighten all the fixings. D472 Cover the visible part of the top bracket on the panel with plastic cover (D), inserting it in the locations provided in the bracket. 11 Once the door has been correctly aligned, tighten the holding nuts on the fixing brackets and attach the appliance to the adjacent units and the bottom of the work surface (Fig. 12 If the appliance has been fitted into a space 820 mm high and the 170 maximum height 220 of the base plate is 100 mm, fit the 600 front cover plate 135 185 by pushing the two D518 vertical lugs into the rectangular holes on the bottom side of the ventilation duct until they click. The plate can be adjusted backwards or forwards in the holes (Fig. 12). 820 870 Insert the adjusting pins (BFig. 7) into their locations in the door and screw them in. D517 D532 Fig. 8 1 Hook the decorative panel onto the top part of C the door, inserting the pins (B) (on the door) into the elongated holes (1) (in the top bracket fitted to the panel) 2 D533 (Fig. Insert the securing screws (C) through elongated holes (2) and fix the panel without tightening the screws (Fig. [. . . ] To stop operation, simply turn the thermostat knob to position «O». Important If the ambient temperature is high or the appliance is fully loaded, and the appliance is set to the lowest temperatures, it may run continuously causing frost to form on the rear wall. In this case the dial must be set to a higher temperature to allow automatic defrosting and therefore reduced energy consumption. D040 The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired. 15 Ice-cube production This appliance is equipped with one or more trays for the production of ice-cubes. [. . . ]